Extended signal quality +CESQ
The +CESQ command returns received signal quality parameters. This command issues a valid response only when the modem is activated.v1.0.xv1.1.xv1.2.xv1.3.x
Signal quality notification %CESQ
The Nordic-proprietary %CESQ command subscribes notifications of changes in signal quality.v1.0.xv1.1.xv1.2.xv1.3.x
Signal quality +CSQ
The +CSQ command reads 2G and 3G signal quality.v1.0.xv1.1.xv1.2.xv1.3.x
IP address format +CGPIAF
The +CGPIAF command returns information about IPv6 address format.v1.0.xv1.1.xv1.2.xv1.3.x
Current band %XCBAND
The Nordic-proprietary %XCBAND command returns the current E-UTRA band.v1.0.xv1.1.xv1.2.xv1.3.x
Neighboring cells %NBRGRSRP
The Nordic-proprietary %NBRGRSRP command reads measured RSRP values of neighboring cells. The command issues a valid response only when the modem is activated.v1.0.xv1.1.xv1.2.xv1.3.x
Band lock %XBANDLOCK
The Nordic-proprietary %XBANDLOCK command sets locked bands.v1.0.xv1.1.xv1.2.xv1.3.x
Data profile %XDATAPRFL
The Nordic-proprietary %XDATAPRFL command can be used to provide information on the application use case to modem so that it can optimize power consumption.v1.0.xv1.1.xv1.2.xv1.3.x
Connectivity statistics %XCONNSTAT
The Nordic-proprietary %XCONNSTAT command starts and stops the collecting of connectivity statistics.v1.0.xv1.1.xv1.2.xv1.3.x
Battery voltage %XVBAT
The Nordic-proprietary %XVBAT command reads battery voltage.v1.0.xv1.1.xv1.2.xv1.3.xpti_v1.1.x≥1
Battery voltage low level %XVBATLOWLVL
The Nordic-proprietary %XVBATLOWLVL command sets the battery voltage low level for a modem. If notifications of battery voltage low level have been subscribed, the modem sends clients a notification when the measured battery voltage is below the defined level. The modem reads sensors periodically in connected mode. The default period is 60 seconds. If the temperature or voltage gets close to the set threshold, a shorter period is used.v1.1.xv1.2.xv1.3.x
External power off warnings %XPOFWARN
The Nordic-proprietary %XPOFWARN command controls the power off warnings from the modem. The command is supported by nRF9160 SIxA B1A.v1.1.x≥3v1.2.x≥1v1.3.x
Customer production done %XPRODDONE
The Nordic-proprietary %XPRODDONE command shall be sent after customer production is done.v1.0.xv1.1.xv1.2.xv1.3.x
Internal temperature notification %XTEMP
The Nordic-proprietary %XTEMP command subscribes unsolicited internal temperature notifications. The modem reads sensors periodically in connected mode. The default period is 60 seconds. If the temperature or voltage gets close to the critical temperature, a shorter period is used.v1.0.xv1.1.xv1.2.xv1.3.x
Clock +CCLK
The +CCLK command sets the clock of the device.v1.0.xv1.1.xv1.2.xv1.3.x
Proprietary clock %CCLK
The Nordic-proprietary %CCLK command sets the real-time clock of the device.v1.1.xv1.2.xv1.3.x
Modem trace activation %XMODEMTRACE
The Nordic-proprietary %XMODEMTRACE command activates modem traces. The trace data is in binary format and can help the Nordic customer support to analyze and resolve issues.v1.0.xv1.1.xv1.2.xv1.3.xpti_v1.1.x≥1
Fallback to SMS only %XSMSFALLBACK
The Nordic-proprietary %XSMSFALLBACK command sets the SMS only fallback functionality. With SMS only fallback, UE triggers a TAU request for SMS only immediately when CS service registration fails with permanent cause. This ensures that SMS services are available as soon as possible after registration. SMS only and SMS only fallback are available only in NB-IoT.v1.0.xv1.1.xv1.2.xv1.3.x
System mode %XSYSTEMMODE
The Nordic-proprietary %XSYSTEMMODE command sets the modem system mode.v1.0.xv1.1.xv1.2.xv1.3.xpti_v1.1.x≥1
Extra maximum TX power reduction %XEMPR
The Nordic-proprietary %XEMPR command allows to configure an extra reduction of 0.5 or 1 dB to the maximum transmission power on all or selected supported 3GPP bands separately in the NB-IoT and LTE-M modes.v1.2.xv1.3.xpti_v1.1.x≥1
Write content to file %XFILEWRITE
The Nordic-proprietary %XFILEWRITE command writes given content to a file.v1.2.xv1.3.xpti_v1.1.x≥1
Factory reset %XFACTORYRESET
The Nordic-proprietary %XFACTORYRESET command resets the modem to factory settings. This operation is allowed only when the modem is not activated.v1.3.x
Modem sleep notification %XMODEMSLEEP
The Nordic-proprietary %XMODEMSLEEP command subscribes modem sleep notifications. Based on the %XMODEMSLEEP indications, the application can optimize its power efficiency by synchronizing its operations to the modem’s sleeps and wake-ups and radio activity and inactivity.v1.3.x
Periodic TAU notification %XT3412
The Nordic-proprietary %XT3412 command subscribes periodic TAU notifications. Based on XT3412 indications, the application can optimize its power efficiency by synchronizing its data transmissions with periodic TAU procedures.v1.3.x
Country-specific search optimization %XCOUNTRYDATA
The Nordic-proprietary %XCOUNTRYDATA command can be used to configure country-specific search parameters. The list contains access technology, band, and EARFCN to be used. The maximum number of countries is 70. v1.3.x
Neighboring cell measurement and notification %NCELLMEAS
The Nordic-proprietary %NCELLMEAS command starts cell search and measurements and reports the channel parameters with a result notification when the measurements are finished. The results can be used, for example, in cellular-based positioning services.v1.3.x
Evaluating connection parameters %CONEVAL
The Nordic-proprietary %CONEVAL command requests an evaluation of the LTE radio signal state and an estimation of the energy efficiency in a cell that the modem would use for data transmission. The information can be used to determine the energy efficiency of data transmission before actual data transmission is started. The %CONEVAL command is the most useful for a static or slow-moving device.v1.3.x