Hardware access layer for managing the SPIM peripheral. More...

Macros
#define	NRF_SPIM_PIN_NOT_CONNECTED 0xFFFFFFFF
	This value can be used as a parameter for the nrf_spim_pins_set function to specify that a given SPI signal (SCK, MOSI, or MISO) shall not be connected to a physical pin.

#define	NRF_SPIM_DCX_CNT_ALL_CMD 0xF
	This value specified in the DCX line configuration causes this line to be set low during whole transmission (all transmitted bytes are marked as command bytes). Any lower value causes the DCX line to be switched from low to high after this number of bytes is transmitted (all remaining bytes are marked as data bytes).

#define	NRF_SPIM_HW_CSN_PRESENT
	Macro for checking if the hardware chip select function is available. More...

Enumerations
enum	nrf_spim_task_t { NRF_SPIM_TASK_START = offsetof(NRF_SPIM_Type, TASKS_START), NRF_SPIM_TASK_STOP = offsetof(NRF_SPIM_Type, TASKS_STOP), NRF_SPIM_TASK_SUSPEND = offsetof(NRF_SPIM_Type, TASKS_SUSPEND), NRF_SPIM_TASK_RESUME = offsetof(NRF_SPIM_Type, TASKS_RESUME) }
	SPIM tasks. More...

enum	nrf_spim_event_t { NRF_SPIM_EVENT_STOPPED = offsetof(NRF_SPIM_Type, EVENTS_STOPPED), NRF_SPIM_EVENT_ENDRX = offsetof(NRF_SPIM_Type, EVENTS_ENDRX), NRF_SPIM_EVENT_END = offsetof(NRF_SPIM_Type, EVENTS_END), NRF_SPIM_EVENT_ENDTX = offsetof(NRF_SPIM_Type, EVENTS_ENDTX), NRF_SPIM_EVENT_STARTED = offsetof(NRF_SPIM_Type, EVENTS_STARTED) }
	SPIM events. More...

enum	nrf_spim_short_mask_t { NRF_SPIM_SHORT_END_START_MASK = SPIM_SHORTS_END_START_Msk, NRF_SPIM_ALL_SHORTS_MASK = SPIM_SHORTS_END_START_Msk }
	SPIM shortcuts. More...

enum	nrf_spim_int_mask_t { NRF_SPIM_INT_STOPPED_MASK = SPIM_INTENSET_STOPPED_Msk, NRF_SPIM_INT_ENDRX_MASK = SPIM_INTENSET_ENDRX_Msk, NRF_SPIM_INT_END_MASK = SPIM_INTENSET_END_Msk, NRF_SPIM_INT_ENDTX_MASK = SPIM_INTENSET_ENDTX_Msk, NRF_SPIM_INT_STARTED_MASK = SPIM_INTENSET_STARTED_Msk, NRF_SPIM_ALL_INTS_MASK }
	SPIM interrupts. More...

enum	nrf_spim_frequency_t { NRF_SPIM_FREQ_125K = SPIM_FREQUENCY_FREQUENCY_K125, NRF_SPIM_FREQ_250K = SPIM_FREQUENCY_FREQUENCY_K250, NRF_SPIM_FREQ_500K = SPIM_FREQUENCY_FREQUENCY_K500, NRF_SPIM_FREQ_1M = SPIM_FREQUENCY_FREQUENCY_M1, NRF_SPIM_FREQ_2M = SPIM_FREQUENCY_FREQUENCY_M2, NRF_SPIM_FREQ_4M = SPIM_FREQUENCY_FREQUENCY_M4, NRF_SPIM_FREQ_8M = (int)SPIM_FREQUENCY_FREQUENCY_M8, NRF_SPIM_FREQ_16M = SPIM_FREQUENCY_FREQUENCY_M16, NRF_SPIM_FREQ_32M = SPIM_FREQUENCY_FREQUENCY_M32 }
	SPI master data rates. More...

enum	nrf_spim_mode_t { NRF_SPIM_MODE_0, NRF_SPIM_MODE_1, NRF_SPIM_MODE_2, NRF_SPIM_MODE_3 }
	SPI modes. More...

enum	nrf_spim_bit_order_t { NRF_SPIM_BIT_ORDER_MSB_FIRST = SPIM_CONFIG_ORDER_MsbFirst, NRF_SPIM_BIT_ORDER_LSB_FIRST = SPIM_CONFIG_ORDER_LsbFirst }
	SPI bit orders. More...

enum	nrf_spim_csn_pol_t { NRF_SPIM_CSN_POL_LOW = SPIM_CSNPOL_CSNPOL_LOW, NRF_SPIM_CSN_POL_HIGH = SPIM_CSNPOL_CSNPOL_HIGH }
	SPI CSN pin polarity. More...

Functions
__STATIC_INLINE void	nrf_spim_task_trigger (NRF_SPIM_Type *p_reg, nrf_spim_task_t task)
	Function for activating the specified SPIM task. More...

__STATIC_INLINE uint32_t	nrf_spim_task_address_get (NRF_SPIM_Type *p_reg, nrf_spim_task_t task)
	Function for getting the address of the specified SPIM task register. More...

__STATIC_INLINE void	nrf_spim_event_clear (NRF_SPIM_Type *p_reg, nrf_spim_event_t event)
	Function for clearing the specified SPIM event. More...

__STATIC_INLINE bool	nrf_spim_event_check (NRF_SPIM_Type *p_reg, nrf_spim_event_t event)
	Function for retrieving the state of the SPIM event. More...

__STATIC_INLINE uint32_t	nrf_spim_event_address_get (NRF_SPIM_Type *p_reg, nrf_spim_event_t event)
	Function for getting the address of the specified SPIM event register. More...

__STATIC_INLINE void	nrf_spim_shorts_enable (NRF_SPIM_Type *p_reg, uint32_t mask)
	Function for enabling the specified shortcuts. More...

__STATIC_INLINE void	nrf_spim_shorts_disable (NRF_SPIM_Type *p_reg, uint32_t mask)
	Function for disabling the specified shortcuts. More...

__STATIC_INLINE uint32_t	nrf_spim_shorts_get (NRF_SPIM_Type *p_reg)
	Function for getting the shortcut setting. More...

__STATIC_INLINE void	nrf_spim_int_enable (NRF_SPIM_Type *p_reg, uint32_t mask)
	Function for enabling the specified interrupts. More...

__STATIC_INLINE void	nrf_spim_int_disable (NRF_SPIM_Type *p_reg, uint32_t mask)
	Function for disabling the specified interrupts. More...

__STATIC_INLINE bool	nrf_spim_int_enable_check (NRF_SPIM_Type *p_reg, nrf_spim_int_mask_t spim_int)
	Function for retrieving the state of a given interrupt. More...

__STATIC_INLINE void	nrf_spim_subscribe_set (NRF_SPIM_Type *p_reg, nrf_spim_task_t task, uint8_t channel)
	Function for setting the subscribe configuration for a given SPIM task. More...

__STATIC_INLINE void	nrf_spim_subscribe_clear (NRF_SPIM_Type *p_reg, nrf_spim_task_t task)
	Function for clearing the subscribe configuration for a given SPIM task. More...

__STATIC_INLINE void	nrf_spim_publish_set (NRF_SPIM_Type *p_reg, nrf_spim_event_t event, uint8_t channel)
	Function for setting the publish configuration for a given SPIM event. More...

__STATIC_INLINE void	nrf_spim_publish_clear (NRF_SPIM_Type *p_reg, nrf_spim_event_t event)
	Function for clearing the publish configuration for a given SPIM event. More...

__STATIC_INLINE void	nrf_spim_enable (NRF_SPIM_Type *p_reg)
	Function for enabling the SPIM peripheral. More...

__STATIC_INLINE void	nrf_spim_disable (NRF_SPIM_Type *p_reg)
	Function for disabling the SPIM peripheral. More...

__STATIC_INLINE void	nrf_spim_pins_set (NRF_SPIM_Type *p_reg, uint32_t sck_pin, uint32_t mosi_pin, uint32_t miso_pin)
	Function for configuring SPIM pins. More...

__STATIC_INLINE void	nrf_spim_csn_configure (NRF_SPIM_Type *p_reg, uint32_t pin, nrf_spim_csn_pol_t polarity, uint32_t duration)
	Function for configuring the SPIM hardware CSN pin. More...

__STATIC_INLINE void	nrf_spim_dcx_pin_set (NRF_SPIM_Type *p_reg, uint32_t dcx_pin)
	Function for configuring the SPIM DCX pin. More...

__STATIC_INLINE void	nrf_spim_dcx_cnt_set (NRF_SPIM_Type *p_reg, uint32_t count)
	Function for configuring the number of command bytes. More...

__STATIC_INLINE void	nrf_spim_iftiming_set (NRF_SPIM_Type *p_reg, uint32_t rxdelay)
	Function for configuring the extended SPIM interface. More...

__STATIC_INLINE void	nrf_spim_stallstat_rx_clear (NRF_SPIM_Type *p_reg)
	Function for clearing stall status for RX EasyDMA RAM accesses. More...

__STATIC_INLINE bool	nrf_spim_stallstat_rx_get (NRF_SPIM_Type *p_reg)
	Function for getting stall status for RX EasyDMA RAM accesses. More...

__STATIC_INLINE void	nrf_spim_stallstat_tx_clear (NRF_SPIM_Type *p_reg)
	Function for clearing stall status for TX EasyDMA RAM accesses. More...

__STATIC_INLINE bool	nrf_spim_stallstat_tx_get (NRF_SPIM_Type *p_reg)
	Function for getting stall status for TX EasyDMA RAM accesses. More...

__STATIC_INLINE void	nrf_spim_frequency_set (NRF_SPIM_Type *p_reg, nrf_spim_frequency_t frequency)
	Function for setting the SPI master data rate. More...

__STATIC_INLINE void	nrf_spim_tx_buffer_set (NRF_SPIM_Type p_reg, uint8_t const p_buffer, size_t length)
	Function for setting the transmit buffer. More...

__STATIC_INLINE void	nrf_spim_rx_buffer_set (NRF_SPIM_Type p_reg, uint8_t p_buffer, size_t length)
	Function for setting the receive buffer. More...

__STATIC_INLINE void	nrf_spim_configure (NRF_SPIM_Type *p_reg, nrf_spim_mode_t spi_mode, nrf_spim_bit_order_t spi_bit_order)
	Function for setting the SPI configuration. More...

__STATIC_INLINE void	nrf_spim_orc_set (NRF_SPIM_Type *p_reg, uint8_t orc)
	Function for setting the over-read character. More...

__STATIC_INLINE void	nrf_spim_tx_list_enable (NRF_SPIM_Type *p_reg)
	Function for enabling the TX list feature. More...

__STATIC_INLINE void	nrf_spim_tx_list_disable (NRF_SPIM_Type *p_reg)
	Function for disabling the TX list feature. More...

__STATIC_INLINE void	nrf_spim_rx_list_enable (NRF_SPIM_Type *p_reg)
	Function for enabling the RX list feature. More...

__STATIC_INLINE void	nrf_spim_rx_list_disable (NRF_SPIM_Type *p_reg)
	Function for disabling the RX list feature. More...

Detailed Description

Hardware access layer for managing the SPIM peripheral.

Macro Definition Documentation

#define NRF_SPIM_HW_CSN_PRESENT

Value:

(NRFX_CHECK(SPIM0_FEATURE_HARDWARE_CSN_PRESENT) || \
 NRFX_CHECK(SPIM1_FEATURE_HARDWARE_CSN_PRESENT) || \
 NRFX_CHECK(SPIM2_FEATURE_HARDWARE_CSN_PRESENT) || \
 NRFX_CHECK(SPIM3_FEATURE_HARDWARE_CSN_PRESENT))

Macro for checking if the hardware chip select function is available.

Enumeration Type Documentation

enum nrf_spim_bit_order_t

SPI bit orders.

Enumerator
NRF_SPIM_BIT_ORDER_MSB_FIRST	Most significant bit shifted out first.
NRF_SPIM_BIT_ORDER_LSB_FIRST	Least significant bit shifted out first.

enum nrf_spim_csn_pol_t

SPI CSN pin polarity.

Enumerator
NRF_SPIM_CSN_POL_LOW	Active low (idle state high).
NRF_SPIM_CSN_POL_HIGH	Active high (idle state low).

enum nrf_spim_event_t

SPIM events.

Enumerator
NRF_SPIM_EVENT_STOPPED	SPI transaction has stopped.
NRF_SPIM_EVENT_ENDRX	End of RXD buffer reached.
NRF_SPIM_EVENT_END	End of RXD buffer and TXD buffer reached.
NRF_SPIM_EVENT_ENDTX	End of TXD buffer reached.
NRF_SPIM_EVENT_STARTED	Transaction started.

enum nrf_spim_frequency_t

SPI master data rates.

Enumerator
NRF_SPIM_FREQ_125K	125 kbps.
NRF_SPIM_FREQ_250K	250 kbps.
NRF_SPIM_FREQ_500K	500 kbps.
NRF_SPIM_FREQ_1M	1 Mbps.
NRF_SPIM_FREQ_2M	2 Mbps.
NRF_SPIM_FREQ_4M	4 Mbps.
NRF_SPIM_FREQ_8M	8 Mbps.
NRF_SPIM_FREQ_16M	16 Mbps.
NRF_SPIM_FREQ_32M	32 Mbps.

enum nrf_spim_int_mask_t

SPIM interrupts.

Enumerator
NRF_SPIM_INT_STOPPED_MASK	Interrupt on STOPPED event.
NRF_SPIM_INT_ENDRX_MASK	Interrupt on ENDRX event.
NRF_SPIM_INT_END_MASK	Interrupt on END event.
NRF_SPIM_INT_ENDTX_MASK	Interrupt on ENDTX event.
NRF_SPIM_INT_STARTED_MASK	Interrupt on STARTED event.
NRF_SPIM_ALL_INTS_MASK	All SPIM interrupts.

enum nrf_spim_mode_t

SPI modes.

Enumerator
NRF_SPIM_MODE_0	SCK active high, sample on leading edge of clock.
NRF_SPIM_MODE_1	SCK active high, sample on trailing edge of clock.
NRF_SPIM_MODE_2	SCK active low, sample on leading edge of clock.
NRF_SPIM_MODE_3	SCK active low, sample on trailing edge of clock.

enum nrf_spim_short_mask_t

SPIM shortcuts.

Enumerator
NRF_SPIM_SHORT_END_START_MASK	Shortcut between END event and START task.
NRF_SPIM_ALL_SHORTS_MASK	All SPIM shortcuts.

enum nrf_spim_task_t

SPIM tasks.

Enumerator
NRF_SPIM_TASK_START	Start SPI transaction.
NRF_SPIM_TASK_STOP	Stop SPI transaction.
NRF_SPIM_TASK_SUSPEND	Suspend SPI transaction.
NRF_SPIM_TASK_RESUME	Resume SPI transaction.

Function Documentation

__STATIC_INLINE void nrf_spim_configure	(	NRF_SPIM_Type *	p_reg,
		nrf_spim_mode_t	spi_mode,
		nrf_spim_bit_order_t	spi_bit_order
	)

Function for setting the SPI configuration.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	spi_mode	SPI mode.
[in]	spi_bit_order	SPI bit order.

__STATIC_INLINE void nrf_spim_csn_configure	(	NRF_SPIM_Type *	p_reg,
		uint32_t	pin,
		nrf_spim_csn_pol_t	polarity,
		uint32_t	duration
	)

Function for configuring the SPIM hardware CSN pin.

If this signal is not needed, pass the NRF_SPIM_PIN_NOT_CONNECTED value instead of its pin number.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	pin	CSN pin number.
[in]	polarity	CSN pin polarity.
[in]	duration	Minimum duration between the edge of CSN and the edge of SCK and minimum duration of CSN must stay unselected between transactions. The value is specified in number of 64 MHz clock cycles (15.625 ns).

__STATIC_INLINE void nrf_spim_dcx_cnt_set	(	NRF_SPIM_Type *	p_reg,
		uint32_t	count
	)

Function for configuring the number of command bytes.

Maximum value available for dividing the transmitted bytes into command bytes and data bytes is NRF_SPIM_DCX_CNT_ALL_CMD - 1. The NRF_SPIM_DCX_CNT_ALL_CMD value passed as the count parameter causes all transmitted bytes to be marked as command bytes.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	count	Number of command bytes preceding the data bytes.

__STATIC_INLINE void nrf_spim_dcx_pin_set	(	NRF_SPIM_Type *	p_reg,
		uint32_t	dcx_pin
	)

Function for configuring the SPIM DCX pin.

If this signal is not needed, pass the NRF_SPIM_PIN_NOT_CONNECTED value instead of its pin number.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	dcx_pin	DCX pin number.

__STATIC_INLINE void nrf_spim_disable ( NRF_SPIM_Type * p_reg )

Function for disabling the SPIM peripheral.

Parameters

[in] p_reg Pointer to the structure of registers of the peripheral.

__STATIC_INLINE void nrf_spim_enable ( NRF_SPIM_Type * p_reg )

Function for enabling the SPIM peripheral.

Parameters

[in] p_reg Pointer to the structure of registers of the peripheral.

__STATIC_INLINE uint32_t nrf_spim_event_address_get	(	NRF_SPIM_Type *	p_reg,
		nrf_spim_event_t	event
	)

Function for getting the address of the specified SPIM event register.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	event	The specified event.

Returns: Address of the specified event register.

__STATIC_INLINE bool nrf_spim_event_check	(	NRF_SPIM_Type *	p_reg,
		nrf_spim_event_t	event
	)

Function for retrieving the state of the SPIM event.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	event	Event to be checked.

Return values

true	The event has been generated.
false	The event has not been generated.

__STATIC_INLINE void nrf_spim_event_clear	(	NRF_SPIM_Type *	p_reg,
		nrf_spim_event_t	event
	)

Function for clearing the specified SPIM event.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	event	Event to be cleared.

__STATIC_INLINE void nrf_spim_frequency_set	(	NRF_SPIM_Type *	p_reg,
		nrf_spim_frequency_t	frequency
	)

Function for setting the SPI master data rate.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	frequency	SPI frequency.

__STATIC_INLINE void nrf_spim_iftiming_set	(	NRF_SPIM_Type *	p_reg,
		uint32_t	rxdelay
	)

Function for configuring the extended SPIM interface.

Parameters

p_reg	Pointer to the structure of registers of the peripheral.
rxdelay	Sample delay for input serial data on MISO, specified in 64 MHz clock cycles (15.625 ns) from the sampling edge of SCK.

__STATIC_INLINE void nrf_spim_int_disable	(	NRF_SPIM_Type *	p_reg,
		uint32_t	mask
	)

Function for disabling the specified interrupts.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	mask	Mask of interrupts to be disabled.

__STATIC_INLINE void nrf_spim_int_enable	(	NRF_SPIM_Type *	p_reg,
		uint32_t	mask
	)

Function for enabling the specified interrupts.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	mask	Mask of interrupts to be enabled.

__STATIC_INLINE bool nrf_spim_int_enable_check	(	NRF_SPIM_Type *	p_reg,
		nrf_spim_int_mask_t	spim_int
	)

Function for retrieving the state of a given interrupt.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	spim_int	Interrupt to be checked.

Return values

true	The interrupt is enabled.
false	The interrupt is not enabled.

__STATIC_INLINE void nrf_spim_orc_set	(	NRF_SPIM_Type *	p_reg,
		uint8_t	orc
	)

Function for setting the over-read character.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	orc	Over-read character that is clocked out in case of an over-read of the TXD buffer.

__STATIC_INLINE void nrf_spim_pins_set	(	NRF_SPIM_Type *	p_reg,
		uint32_t	sck_pin,
		uint32_t	mosi_pin,
		uint32_t	miso_pin
	)

Function for configuring SPIM pins.

If a given signal is not needed, pass the NRF_SPIM_PIN_NOT_CONNECTED value instead of its pin number.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	sck_pin	SCK pin number.
[in]	mosi_pin	MOSI pin number.
[in]	miso_pin	MISO pin number.

__STATIC_INLINE void nrf_spim_publish_clear	(	NRF_SPIM_Type *	p_reg,
		nrf_spim_event_t	event
	)

Function for clearing the publish configuration for a given SPIM event.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	event	Event for which to clear the configuration.

__STATIC_INLINE void nrf_spim_publish_set	(	NRF_SPIM_Type *	p_reg,
		nrf_spim_event_t	event,
		uint8_t	channel
	)

Function for setting the publish configuration for a given SPIM event.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	event	Event for which to set the configuration.
[in]	channel	Channel through which to publish the event.

__STATIC_INLINE void nrf_spim_rx_buffer_set	(	NRF_SPIM_Type *	p_reg,
		uint8_t *	p_buffer,
		size_t	length
	)

Function for setting the receive buffer.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	p_buffer	Pointer to the buffer for received data.
[in]	length	Maximum number of data bytes to receive.

__STATIC_INLINE void nrf_spim_rx_list_disable ( NRF_SPIM_Type * p_reg )

Function for disabling the RX list feature.

Parameters

[in] p_reg Pointer to the structure of registers of the peripheral.

__STATIC_INLINE void nrf_spim_rx_list_enable ( NRF_SPIM_Type * p_reg )

Function for enabling the RX list feature.

Parameters

[in] p_reg Pointer to the structure of registers of the peripheral.

__STATIC_INLINE void nrf_spim_shorts_disable	(	NRF_SPIM_Type *	p_reg,
		uint32_t	mask
	)

Function for disabling the specified shortcuts.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	mask	Shortcuts to be disabled.

__STATIC_INLINE void nrf_spim_shorts_enable	(	NRF_SPIM_Type *	p_reg,
		uint32_t	mask
	)

Function for enabling the specified shortcuts.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	mask	Shortcuts to be enabled.

__STATIC_INLINE uint32_t nrf_spim_shorts_get ( NRF_SPIM_Type * p_reg )

Function for getting the shortcut setting.

Parameters

[in] p_reg Pointer to the structure of registers of the peripheral.

Returns: Current shortcut configuration.

__STATIC_INLINE void nrf_spim_stallstat_rx_clear ( NRF_SPIM_Type * p_reg )

Function for clearing stall status for RX EasyDMA RAM accesses.

Parameters

p_reg Pointer to the structure of registers of the peripheral.

__STATIC_INLINE bool nrf_spim_stallstat_rx_get ( NRF_SPIM_Type * p_reg )

Function for getting stall status for RX EasyDMA RAM accesses.

Parameters

p_reg Pointer to the structure of registers of the peripheral.

Returns: Stall status of RX EasyDMA RAM accesses.

__STATIC_INLINE void nrf_spim_stallstat_tx_clear ( NRF_SPIM_Type * p_reg )

Function for clearing stall status for TX EasyDMA RAM accesses.

Parameters

p_reg Pointer to the structure of registers of the peripheral.

__STATIC_INLINE bool nrf_spim_stallstat_tx_get ( NRF_SPIM_Type * p_reg )

Function for getting stall status for TX EasyDMA RAM accesses.

Parameters

p_reg Pointer to the structure of registers of the peripheral.

Returns: Stall status of TX EasyDMA RAM accesses.

__STATIC_INLINE void nrf_spim_subscribe_clear	(	NRF_SPIM_Type *	p_reg,
		nrf_spim_task_t	task
	)

Function for clearing the subscribe configuration for a given SPIM task.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	task	Task for which to clear the configuration.

__STATIC_INLINE void nrf_spim_subscribe_set	(	NRF_SPIM_Type *	p_reg,
		nrf_spim_task_t	task,
		uint8_t	channel
	)

Function for setting the subscribe configuration for a given SPIM task.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	task	Task for which to set the configuration.
[in]	channel	Channel through which to subscribe events.

__STATIC_INLINE uint32_t nrf_spim_task_address_get	(	NRF_SPIM_Type *	p_reg,
		nrf_spim_task_t	task
	)

Function for getting the address of the specified SPIM task register.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	task	The specified task.

Returns: Address of the specified task register.

__STATIC_INLINE void nrf_spim_task_trigger	(	NRF_SPIM_Type *	p_reg,
		nrf_spim_task_t	task
	)

Function for activating the specified SPIM task.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	task	Task to be activated.

__STATIC_INLINE void nrf_spim_tx_buffer_set	(	NRF_SPIM_Type *	p_reg,
		uint8_t const *	p_buffer,
		size_t	length
	)

Function for setting the transmit buffer.

Parameters

[in]	p_reg	Pointer to the structure of registers of the peripheral.
[in]	p_buffer	Pointer to the buffer with data to send.
[in]	length	Maximum number of data bytes to transmit.

__STATIC_INLINE void nrf_spim_tx_list_disable ( NRF_SPIM_Type * p_reg )

Function for disabling the TX list feature.

Parameters

[in] p_reg Pointer to the structure of registers of the peripheral.

__STATIC_INLINE void nrf_spim_tx_list_enable ( NRF_SPIM_Type * p_reg )

Function for enabling the TX list feature.

Parameters

[in] p_reg Pointer to the structure of registers of the peripheral.

Macros

Enumerations

Functions

Detailed Description

Macro Definition Documentation

Enumeration Type Documentation

Function Documentation