Thermostat cluster attribute identifiers.
Enumerator |
---|
ZB_ZCL_ATTR_THERMOSTAT_LOCAL_TEMPERATURE_ID |
Local Temperature attribute.
|
ZB_ZCL_ATTR_THERMOSTAT_OUTDOOR_TEMPERATURE_ID |
OutdoorTemperature represents the outdoor temperature in degrees Celsius, as measured locally or remotely (over the network).
|
ZB_ZCL_ATTR_THERMOSTAT_OCCUPANCY_ID |
Occupancy specifies whether the heated/cooled space is occupied or not, as measured locally or remotely (over the network).
|
ZB_ZCL_ATTR_THERMOSTAT_ABS_MIN_HEAT_SETPOINT_LIMIT_ID |
The AbsMinHeatSetpointLimit attribute specifies the absolute minimum level that the heating setpoint MAY be set to.
|
ZB_ZCL_ATTR_THERMOSTAT_ABS_MAX_HEAT_SETPOINT_LIMIT_ID |
The AbsMaxHeatSetpointLimit attribute specifies the absolute maximum level that the heating setpoint MAY be set to.
|
ZB_ZCL_ATTR_THERMOSTAT_ABS_MIN_COOL_SETPOINT_LIMIT_ID |
The AbsMinCoolSetpointLimit attribute specifies the absolute minimum level that the cooling setpoint MAY be set to.
|
ZB_ZCL_ATTR_THERMOSTAT_ABS_MAX_COOL_SETPOINT_LIMIT_ID |
The AbsMaxCoolSetpointLimit attribute specifies the absolute maximum level that the cooling setpoint MAY be set to.
|
ZB_ZCL_ATTR_THERMOSTAT_PI_COOLING_DEMAND_ID |
The PICoolingDemand attribute is 8 bits in length and specifies the level of cooling demanded by the PI (proportional integral) control loop in use by the thermostat (if any), in percent.
|
ZB_ZCL_ATTR_THERMOSTAT_PI_HEATING_DEMAND_ID |
The PIHeatingDemand attribute is 8 bits in length and specifies the level of heating demanded by the PI loop in percent.
|
ZB_ZCL_ATTR_THERMOSTAT_HVAC_SYSTEM_TYPE_CONFIGURATION_ID |
The HVACSystemTypeConfiguration attribute specifies the HVAC system type controlled by the thermostat.
|
ZB_ZCL_ATTR_THERMOSTAT_LOCAL_TEMPERATURE_CALIBRATION_ID |
Local Temperature Calibration.
|
ZB_ZCL_ATTR_THERMOSTAT_OCCUPIED_COOLING_SETPOINT_ID |
Occupied Cooling Setpoint attribute.
|
ZB_ZCL_ATTR_THERMOSTAT_OCCUPIED_HEATING_SETPOINT_ID |
Occupied Heating Setpoint attribute.
|
ZB_ZCL_ATTR_THERMOSTAT_UNOCCUPIED_COOLING_SETPOINT_ID |
Unoccupied Cooling Setpoint attribute.
|
ZB_ZCL_ATTR_THERMOSTAT_UNOCCUPIED_HEATING_SETPOINT_ID |
Unoccupied Heating Setpoint attribute.
|
ZB_ZCL_ATTR_THERMOSTAT_MIN_HEAT_SETPOINT_LIMIT_ID |
The MinHeatSetpointLimit attribute specifies the minimum level that the heating setpoint MAY be set to.
|
ZB_ZCL_ATTR_THERMOSTAT_MAX_HEAT_SETPOINT_LIMIT_ID |
The MaxHeatSetpointLimit attribute specifies the maximum level that the heating setpoint MAY be set to.
|
ZB_ZCL_ATTR_THERMOSTAT_MIN_COOL_SETPOINT_LIMIT_ID |
The MinCoolSetpointLimit attribute specifies the minimum level that the cooling setpoint MAY be set to.
|
ZB_ZCL_ATTR_THERMOSTAT_MAX_COOL_SETPOINT_LIMIT_ID |
The MaxCoolSetpointLimit attribute specifies the maximum level that the cooling setpoint MAY be set to.
|
ZB_ZCL_ATTR_THERMOSTAT_MIN_SETPOINT_DEAD_BAND_ID |
The MinSetpointDeadBand attribute specifies the minimum difference between the Heat Setpoint and the Cool SetPoint, in steps of 0.1C.
|
ZB_ZCL_ATTR_THERMOSTAT_REMOTE_SENSING_ID |
The RemoteSensing attribute is an 8-bit bitmap that specifies whether the local temperature, outdoor temperature and occupancy are being sensed by internal sensors or remote networked sensors.
|
ZB_ZCL_ATTR_THERMOSTAT_CONTROL_SEQUENCE_OF_OPERATION_ID |
Control Sequence Of Operation attribute.
|
ZB_ZCL_ATTR_THERMOSTAT_SYSTEM_MODE_ID |
System Mode attribute.
|
ZB_ZCL_ATTR_THERMOSTAT_ALARM_MASK_ID |
The AlarmMask attribute specifies whether each of the alarms is enabled.
|
ZB_ZCL_ATTR_THERMOSTAT_RUNNING_MODE_ID |
Thermostat Running Mode attribute.
|
ZB_ZCL_ATTR_THERMOSTAT_NUMBER_OF_WEEKLY_TRANSITIONS_ID |
NumberOfWeeklyTransitions attribute determines how many weekly schedule transitions the thermostat is capable of handling.
|
ZB_ZCL_ATTR_THERMOSTAT_NUMBER_OF_DAILY_TRANSITIONS_ID |
NumberOfDailyTransitions attribute determines how many daily schedule transitions the thermostat is capable of handling.
|
ZB_ZCL_ATTR_THERMOSTAT_TEMPERATURE_SETPOINT_HOLD_ID |
TemperatureSetpointHold specifies the temperature hold status on the thermostat.
|
ZB_ZCL_ATTR_THERMOSTAT_TEMPERATURE_SETPOINT_HOLD_DURATION_ID |
TemperatureSetpointHoldDuration sets the period in minutes for which a setpoint hold is active.
|
ZB_ZCL_ATTR_THERMOSTAT_THERMOSTAT_PROGRAMMING_OPERATION_MODE_ID |
The ThermostatProgrammingOperationMode attribute determines the operational state of the thermostats programming.
|
ZB_ZCL_ATTR_THERMOSTAT_THERMOSTAT_RUNNING_STATE_ID |
ThermostatRunningState represents the current relay state of the heat, cool, and fan relays.
|
ZB_ZCL_ATTR_THERMOSTAT_SETPOINT_CHANGE_SOURCE_ID |
The SetpointChangeSource attribute specifies the source of the current active OccupiedCoolingSetpoint or OccupiedHeatingSetpoint (i.e., who or what determined the current setpoint).
|
ZB_ZCL_ATTR_THERMOSTAT_SETPOINT_CHANGE_AMOUNT_ID |
The SetpointChangeAmount attribute specifies the delta between the current active OccupiedCoolingSetpoint or OccupiedHeatingSetpoint and the previous active setpoint.
|
ZB_ZCL_ATTR_THERMOSTAT_SETPOINT_CHANGE_SOURCE_TIMESTAMP_ID |
The SetpointChangeSourceTimestamp attribute specifies the time in UTC at which the SetpointChangeSourceAmount attribute change was recorded.
|
ZB_ZCL_ATTR_THERMOSTAT_OCCUPIED_SETBACK_ID |
Specifies the degrees Celsius, in 0.1 degree increments, the Thermostat server will allow the LocalTemperature attribute to float above the OccupiedCooling setpoint (i.e., OccupiedCooling + OccupiedSetback) or below the OccupiedHeating setpoint (i.e., occupiedHeating, OccupiedSetback) before initiating a state change to bring the temperature back to the users desired setpoint.
|
ZB_ZCL_ATTR_THERMOSTAT_OCCUPIED_SETBACK_MIN_ID |
Specifies the minimum degrees Celsius, in 0.1 degree increments, the Thermostat server will allow the OccupiedSetback attribute to be configured by a user.
|
ZB_ZCL_ATTR_THERMOSTAT_OCCUPIED_SETBACK_MAX_ID |
Specifies the maximum degrees Celsius, in 0.1 degree increments, the Thermostat server will allow the OccupiedSetback attribute to be configured by a user.
|
ZB_ZCL_ATTR_THERMOSTAT_UNOCCUPIED_SETBACK_ID |
Specifies the degrees Celsius, in 0.1 degree increments, the Thermostat server will allow the LocalTemperature attribute to float above the UnoccupiedCooling setpoint (i.e., UnoccupiedCooling + UnoccupiedSetback) or below the UnoccupiedHeating setpoint (i.e., UnoccupiedHeating - UnoccupiedSetback) before initiating a state change to bring the temperature back to the users desired setpoint.
|
ZB_ZCL_ATTR_THERMOSTAT_UNOCCUPIED_SETBACK_MIN_ID |
Specifies the minimum degrees Celsius, in 0.1 degree increments, the Thermostat server will allow the UnoccupiedSetback attribute to be configured by a user.
|
ZB_ZCL_ATTR_THERMOSTAT_UNOCCUPIED_SETBACK_MAX_ID |
Specifies the maximum degrees Celsius, in 0.1 degree increments, the Thermostat server will allow the UnoccupiedSetback attribute to be configured by a user.
|
ZB_ZCL_ATTR_THERMOSTAT_EMERGENCY_HEAT_DELTA_ID |
Specifies the delta, in 0.1 degrees Celsius, between LocalTemperature and the OccupiedHeatingSetpoint or UnoccupiedHeatingSetpoint attributes at which the Thermostat server will operate in emergency heat mode.
|
ZB_ZCL_ATTR_THERMOSTAT_AC_TYPE_ID |
Indicates the type of Mini Split ACType of Mini Split AC is defined depending on how Cooling and Heating condition is achieved by Mini Split AC.
|
ZB_ZCL_ATTR_THERMOSTAT_AC_CAPACITY_ID |
Indicates capacity of Mini Split AC in terms of the format defined by the ACCapacityFormat attribute.
|
ZB_ZCL_ATTR_THERMOSTAT_AC_REFRIGERANT_TYPE_ID |
Indicates type of refrigerant used within the Mini Split AC.
|
ZB_ZCL_ATTR_THERMOSTAT_AC_COMPRESSOR_TYPE_ID |
This indicates type of Compressor used within the Mini Split AC.
|
ZB_ZCL_ATTR_THERMOSTAT_AC_ERROR_CODE_ID |
This indicates the type of errors encountered within the Mini Split AC.
|
ZB_ZCL_ATTR_THERMOSTAT_AC_LOUVER_POSITION_ID |
AC Louver position attribute.
|
ZB_ZCL_ATTR_THERMOSTAT_AC_COIL_TEMPERATURE_ID |
ACCoilTemperature represents the temperature in degrees Celsius, as measured locally or remotely (over the network).
|
ZB_ZCL_ATTR_THERMOSTAT_AC_CAPACITY_FORMAT_ID |
This is the format for the ACCapacity attribute.
|