The SPI master can communicate with multiple SPI slaves using individual chip select signals for each slave.
Listed here are the main features for the SPIM:
An SPI master transaction is started by triggering the START task. When started, a number of bytes will be transmitted/received on MOSI/MISO.
The following figure illustrates an SPI master transaction.
The ENDTX is generated when all bytes in buffer TXD.PTR are transmitted. The number of bytes in the transmit buffer is specified in register TXD.MAXCNT. The ENDRX event will be generated when buffer RXD.PTR is full, meaning the number of bytes specified in register RXD.MAXCNT have been received. The transaction stops automatically after all bytes have been transmitted/received. When the maximum number of bytes in the receive buffer is larger than the number of bytes in the transmit buffer, the contents of register ORC will be transmitted after the last byte in the transmit buffer has been transmitted.
The END event will be generated after both the ENDRX and ENDTX events have been generated.
The SPI master can be stopped in the middle of a transaction by triggering the STOP task. When triggering the STOP task, SPIM will complete the transmission/reception of the current byte before stopping. A STOPPED event is generated when the SPI master has stopped.
If the ENDTX event has not already been generated when the SPI master has come to a stop, the ENDTX event will be generated even if all bytes in the buffer TXD.PTR have not been transmitted.
If the ENDRX event has not already been generated when the SPI master has come to a stop, the ENDRX event will be generated even if the buffer RXD.PTR is not full.
A transaction can be suspended and resumed using the SUSPEND and RESUME tasks. When the SUSPEND task is triggered, the SPI master will complete transmitting and receiving the current ongoing byte before it is suspended.
Some SPI slaves, for example display drivers, require an additional signal from the SPI master to distinguish between command and data bytes. For display drivers this line is often called D/CX.
SPIM provides support for such a D/CX output line. The D/CX line is set low during transmission of command bytes and high during transmission of data bytes.
The D/CX pin number is selected using PSELDCX and the number of command bytes preceding the data bytes is configured using DCXCNT.
It is not allowed to write to the DCXCNT during an ongoing transmission.
The SCK, CSN, DCX, MOSI, and MISO signals associated with SPIM are mapped to physical pins according to the configuration specified in the PSEL.n registers.
The contents of registers PSEL.SCK, PSEL.CSN, PSELDCX, PSEL.MOSI, and PSEL.MISO are only used when SPIM is enabled, and retained only as long as the device is in System ON mode. The PSEL.n registers can only be configured when SPIM is disabled. Enabling/disabling is done using register ENABLE.
To ensure correct behavior, the pins used by SPIM must be configured in the GPIO peripheral as described in GPIO configuration before SPIM is enabled.
Only one peripheral can be assigned to drive a particular GPIO pin at a time. Failing to do so may result in unpredictable behavior.
SPI master signal | SPI master pin | Direction | Output value | Comments |
---|---|---|---|---|
SCK | As specified in PSEL.SCK | Output | Same as CONFIG.CPOL | |
CSN | As specified in PSEL.CSN | Output | Same as CONFIG.CPOL | |
DCX | As specified in PSELDCX | Output | 1 | |
MOSI | As specified in PSEL.MOSI | Output | 0 | |
MISO | As specified in PSEL.MISO | Input | Not applicable |
Some SPIM instances do not support automatic control of CSN, and for those the available GPIO pins need to be used to control CSN directly. See Instances for information about what features are supported in the various SPIM instances.
SPIM supports SPI modes 0 through 3. The clock polarity (CPOL) and the clock phase (CPHA) are configured in register CONFIG.
Mode | Clock polarity | Clock phase |
---|---|---|
CPOL | CPHA | |
SPI_MODE0 | 0 (Active High) | 0 (Leading) |
SPI_MODE1 | 0 (Active High) | 1 (Trailing) |
SPI_MODE2 | 1 (Active Low) | 0 (Leading) |
SPI_MODE3 | 1 (Active Low) | 1 (Trailing) |
SPIM implements EasyDMA for accessing RAM without CPU involvement.
For detailed information regarding the use of EasyDMA, see EasyDMA.
The .PTR and .MAXCNT registers are double-buffered. They can be updated and prepared for the next transmission immediately after having received the STARTED event.
The SPI master will automatically stop transmitting after TXD.MAXCNT bytes have been transmitted and RXD.MAXCNT bytes have been received. If RXD.MAXCNT is larger than TXD.MAXCNT, the remaining transmitted bytes will contain the value defined in the ORC register. If TXD.MAXCNT is larger than RXD.MAXCNT, the superfluous received bytes will be discarded.
The ENDRX/ENDTX event indicate that EasyDMA has finished accessing respectively the RX/TX buffer in RAM. The END event gets generated when both RX and TX are finished accessing the buffers in RAM.
If several AHB bus masters try to access the same AHB slave at the same time, AHB bus congestion might occur, and the behaviour of the EasyDMA channel will depend on the SPIM instance. Refer to Instances for information about what behaviour is supported in the various instances.
When putting the system in low power and the peripheral is not needed, lowest possible power consumption is achieved by stopping, and then disabling the peripheral.
The STOP task may not be always needed (the peripheral might already be stopped), but if it is sent, software shall wait until the STOPPED event was received as a response before disabling the peripheral through the ENABLE register.
Base address | Peripheral | Instance | Description | Configuration | |
---|---|---|---|---|---|
0x40003000 | SPIM | SPIM0 |
SPI master 0 |
Not supported: > 8 Mbps data rate, CSNPOL register, DCX functionality, IFTIMING.x registers, hardware CSN control (PSEL.CSN), stalling mechanism during AHB bus contention. |
|
0x40004000 | SPIM | SPIM1 |
SPI master 1 |
Not supported: > 8 Mbps data rate, CSNPOL register, DCX functionality, IFTIMING.x registers, hardware CSN control (PSEL.CSN), stalling mechanism during AHB bus contention. |
|
0x40023000 | SPIM | SPIM2 |
SPI master 2 |
Not supported: > 8 Mbps data rate, CSNPOL register, DCX functionality, IFTIMING.x registers, hardware CSN control (PSEL.CSN), stalling mechanism during AHB bus contention. |
|
0x4002F000 | SPIM | SPIM3 |
SPI master 3 |
Register | Offset | Description | |
---|---|---|---|
TASKS_START | 0x010 |
Start SPI transaction |
|
TASKS_STOP | 0x014 |
Stop SPI transaction |
|
TASKS_SUSPEND | 0x01C |
Suspend SPI transaction |
|
TASKS_RESUME | 0x020 |
Resume SPI transaction |
|
EVENTS_STOPPED | 0x104 |
SPI transaction has stopped |
|
EVENTS_ENDRX | 0x110 |
End of RXD buffer reached |
|
EVENTS_END | 0x118 |
End of RXD buffer and TXD buffer reached |
|
EVENTS_ENDTX | 0x120 |
End of TXD buffer reached |
|
EVENTS_STARTED | 0x14C |
Transaction started |
|
SHORTS | 0x200 |
Shortcuts between local events and tasks |
|
INTENSET | 0x304 |
Enable interrupt |
|
INTENCLR | 0x308 |
Disable interrupt |
|
STALLSTAT | 0x400 |
Stall status for EasyDMA RAM accesses. The fields in this register are set to STALL by hardware whenever a stall occurs and can be cleared (set to NOSTALL) by the CPU. |
|
ENABLE | 0x500 |
Enable SPIM |
|
PSEL.SCK | 0x508 |
Pin select for SCK |
|
PSEL.MOSI | 0x50C |
Pin select for MOSI signal |
|
PSEL.MISO | 0x510 |
Pin select for MISO signal |
|
PSEL.CSN | 0x514 |
Pin select for CSN |
|
FREQUENCY | 0x524 |
SPI frequency. Accuracy depends on the HFCLK source selected. |
|
RXD.PTR | 0x534 |
Data pointer |
|
RXD.MAXCNT | 0x538 |
Maximum number of bytes in receive buffer |
|
RXD.AMOUNT | 0x53C |
Number of bytes transferred in the last transaction |
|
RXD.LIST | 0x540 |
EasyDMA list type |
|
TXD.PTR | 0x544 |
Data pointer |
|
TXD.MAXCNT | 0x548 |
Number of bytes in transmit buffer |
|
TXD.AMOUNT | 0x54C |
Number of bytes transferred in the last transaction |
|
TXD.LIST | 0x550 |
EasyDMA list type |
|
CONFIG | 0x554 |
Configuration register |
|
IFTIMING.RXDELAY | 0x560 |
Sample delay for input serial data on MISO |
|
IFTIMING.CSNDUR | 0x564 |
Minimum duration between edge of CSN and edge of SCK and minimum duration CSN must stay high between transactions |
|
CSNPOL | 0x568 |
Polarity of CSN output |
|
PSELDCX | 0x56C |
Pin select for DCX signal |
|
DCXCNT | 0x570 |
DCX configuration |
|
ORC | 0x5C0 |
Byte transmitted after TXD.MAXCNT bytes have been transmitted in the case when RXD.MAXCNT is greater than TXD.MAXCNT |
Address offset: 0x010
Start SPI transaction
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | A | ||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | W |
TASKS_START |
Start SPI transaction |
||||||||||||||||||||||||||||||||
Trigger |
1 |
Trigger task |
Address offset: 0x014
Stop SPI transaction
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | A | ||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | W |
TASKS_STOP |
Stop SPI transaction |
||||||||||||||||||||||||||||||||
Trigger |
1 |
Trigger task |
Address offset: 0x01C
Suspend SPI transaction
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | A | ||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | W |
TASKS_SUSPEND |
Suspend SPI transaction |
||||||||||||||||||||||||||||||||
Trigger |
1 |
Trigger task |
Address offset: 0x020
Resume SPI transaction
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | A | ||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | W |
TASKS_RESUME |
Resume SPI transaction |
||||||||||||||||||||||||||||||||
Trigger |
1 |
Trigger task |
Address offset: 0x104
SPI transaction has stopped
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | A | ||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
EVENTS_STOPPED |
SPI transaction has stopped |
||||||||||||||||||||||||||||||||
NotGenerated |
0 |
Event not generated |
|||||||||||||||||||||||||||||||||
Generated |
1 |
Event generated |
Address offset: 0x110
End of RXD buffer reached
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | A | ||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
EVENTS_ENDRX |
End of RXD buffer reached |
||||||||||||||||||||||||||||||||
NotGenerated |
0 |
Event not generated |
|||||||||||||||||||||||||||||||||
Generated |
1 |
Event generated |
Address offset: 0x118
End of RXD buffer and TXD buffer reached
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | A | ||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
EVENTS_END |
End of RXD buffer and TXD buffer reached |
||||||||||||||||||||||||||||||||
NotGenerated |
0 |
Event not generated |
|||||||||||||||||||||||||||||||||
Generated |
1 |
Event generated |
Address offset: 0x120
End of TXD buffer reached
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | A | ||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
EVENTS_ENDTX |
End of TXD buffer reached |
||||||||||||||||||||||||||||||||
NotGenerated |
0 |
Event not generated |
|||||||||||||||||||||||||||||||||
Generated |
1 |
Event generated |
Address offset: 0x14C
Transaction started
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | A | ||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
EVENTS_STARTED |
Transaction started |
||||||||||||||||||||||||||||||||
NotGenerated |
0 |
Event not generated |
|||||||||||||||||||||||||||||||||
Generated |
1 |
Event generated |
Address offset: 0x200
Shortcuts between local events and tasks
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | A | ||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
END_START |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable shortcut |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Enable shortcut |
Address offset: 0x304
Enable interrupt
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | E | D | C | B | A | ||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
STOPPED |
Write '1' to enable interrupt for event STOPPED |
||||||||||||||||||||||||||||||||
Set |
1 |
Enable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
B | RW |
ENDRX |
Write '1' to enable interrupt for event ENDRX |
||||||||||||||||||||||||||||||||
Set |
1 |
Enable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
C | RW |
END |
Write '1' to enable interrupt for event END |
||||||||||||||||||||||||||||||||
Set |
1 |
Enable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
D | RW |
ENDTX |
Write '1' to enable interrupt for event ENDTX |
||||||||||||||||||||||||||||||||
Set |
1 |
Enable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
E | RW |
STARTED |
Write '1' to enable interrupt for event STARTED |
||||||||||||||||||||||||||||||||
Set |
1 |
Enable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
Address offset: 0x308
Disable interrupt
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | E | D | C | B | A | ||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
STOPPED |
Write '1' to disable interrupt for event STOPPED |
||||||||||||||||||||||||||||||||
Clear |
1 |
Disable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
B | RW |
ENDRX |
Write '1' to disable interrupt for event ENDRX |
||||||||||||||||||||||||||||||||
Clear |
1 |
Disable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
C | RW |
END |
Write '1' to disable interrupt for event END |
||||||||||||||||||||||||||||||||
Clear |
1 |
Disable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
D | RW |
ENDTX |
Write '1' to disable interrupt for event ENDTX |
||||||||||||||||||||||||||||||||
Clear |
1 |
Disable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
E | RW |
STARTED |
Write '1' to disable interrupt for event STARTED |
||||||||||||||||||||||||||||||||
Clear |
1 |
Disable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
Address offset: 0x400
Stall status for EasyDMA RAM accesses. The fields in this register are set to STALL by hardware whenever a stall occurs and can be cleared (set to NOSTALL) by the CPU.
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
B |
A |
|||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
TX |
[1..0] |
Stall status for EasyDMA RAM reads |
|||||||||||||||||||||||||||||||
NOSTALL |
0 |
No stall |
|||||||||||||||||||||||||||||||||
STALL |
1 |
A stall has occurred |
|||||||||||||||||||||||||||||||||
B | RW |
RX |
[1..0] |
Stall status for EasyDMA RAM writes |
|||||||||||||||||||||||||||||||
NOSTALL |
0 |
No stall |
|||||||||||||||||||||||||||||||||
STALL |
1 |
A stall has occurred |
Address offset: 0x500
Enable SPIM
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | A | A | A | A | |||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
ENABLE |
Enable or disable SPIM |
||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable SPIM |
|||||||||||||||||||||||||||||||||
Enabled |
7 |
Enable SPIM |
Address offset: 0x508
Pin select for SCK
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | C |
B |
A | A | A | A | A | ||||||||||||||||||||||||||||
Reset 0xFFFFFFFF | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
PIN |
[0..31] |
Pin number |
|||||||||||||||||||||||||||||||
B | RW |
PORT |
[0..1] |
Port number |
|||||||||||||||||||||||||||||||
C | RW |
CONNECT |
Connection |
||||||||||||||||||||||||||||||||
Disconnected |
1 |
Disconnect |
|||||||||||||||||||||||||||||||||
Connected |
0 |
Connect |
Address offset: 0x50C
Pin select for MOSI signal
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | C |
B |
A | A | A | A | A | ||||||||||||||||||||||||||||
Reset 0xFFFFFFFF | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
PIN |
[0..31] |
Pin number |
|||||||||||||||||||||||||||||||
B | RW |
PORT |
[0..1] |
Port number |
|||||||||||||||||||||||||||||||
C | RW |
CONNECT |
Connection |
||||||||||||||||||||||||||||||||
Disconnected |
1 |
Disconnect |
|||||||||||||||||||||||||||||||||
Connected |
0 |
Connect |
Address offset: 0x510
Pin select for MISO signal
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | C |
B |
A | A | A | A | A | ||||||||||||||||||||||||||||
Reset 0xFFFFFFFF | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
PIN |
[0..31] |
Pin number |
|||||||||||||||||||||||||||||||
B | RW |
PORT |
[0..1] |
Port number |
|||||||||||||||||||||||||||||||
C | RW |
CONNECT |
Connection |
||||||||||||||||||||||||||||||||
Disconnected |
1 |
Disconnect |
|||||||||||||||||||||||||||||||||
Connected |
0 |
Connect |
Address offset: 0x514
Pin select for CSN
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
C |
B |
A |
A |
A |
A |
A |
||||||||||||||||||||||||||||
Reset 0xFFFFFFFF | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
PIN |
[0..31] |
Pin number |
|||||||||||||||||||||||||||||||
B | RW |
PORT |
[0..1] |
Port number |
|||||||||||||||||||||||||||||||
C | RW |
CONNECT |
Connection |
||||||||||||||||||||||||||||||||
Disconnected |
1 |
Disconnect |
|||||||||||||||||||||||||||||||||
Connected |
0 |
Connect |
Address offset: 0x524
SPI frequency. Accuracy depends on the HFCLK source selected.
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | |||
Reset 0x04000000 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
FREQUENCY |
SPI master data rate |
||||||||||||||||||||||||||||||||
K125 |
0x02000000 |
125 kbps |
|||||||||||||||||||||||||||||||||
K250 |
0x04000000 |
250 kbps |
|||||||||||||||||||||||||||||||||
K500 |
0x08000000 |
500 kbps |
|||||||||||||||||||||||||||||||||
M1 |
0x10000000 |
1 Mbps |
|||||||||||||||||||||||||||||||||
M2 |
0x20000000 |
2 Mbps |
|||||||||||||||||||||||||||||||||
M4 |
0x40000000 |
4 Mbps |
|||||||||||||||||||||||||||||||||
M8 |
0x80000000 |
8 Mbps |
|||||||||||||||||||||||||||||||||
M16 |
0x0A000000 |
16 Mbps |
|||||||||||||||||||||||||||||||||
M32 |
0x14000000 |
32 Mbps |
Address offset: 0x534
Data pointer
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | |||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
PTR |
Data pointer See the memory chapter for details about which memories are available for EasyDMA. |
Address offset: 0x538
Maximum number of bytes in receive buffer
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | |||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
MAXCNT |
[0..0xFFFF] |
Maximum number of bytes in receive buffer |
Address offset: 0x53C
Number of bytes transferred in the last transaction
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | |||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | R |
AMOUNT |
[0..0xFFFF] |
Number of bytes transferred in the last transaction |
Address offset: 0x540
EasyDMA list type
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | A | A | |||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
LIST |
List type |
||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable EasyDMA list |
|||||||||||||||||||||||||||||||||
ArrayList |
1 |
Use array list |
Address offset: 0x544
Data pointer
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | |||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
PTR |
Data pointer See the memory chapter for details about which memories are available for EasyDMA. |
Address offset: 0x548
Number of bytes in transmit buffer
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | |||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
MAXCNT |
[0..0xFFFF] |
Maximum number of bytes in transmit buffer |
Address offset: 0x54C
Number of bytes transferred in the last transaction
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | A | |||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | R |
AMOUNT |
[0..0xFFFF] |
Number of bytes transferred in the last transaction |
Address offset: 0x550
EasyDMA list type
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | A | A | |||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
LIST |
List type |
||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable EasyDMA list |
|||||||||||||||||||||||||||||||||
ArrayList |
1 |
Use array list |
Address offset: 0x554
Configuration register
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | C | B | A | ||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
ORDER |
Bit order |
||||||||||||||||||||||||||||||||
MsbFirst |
0 |
Most significant bit shifted out first |
|||||||||||||||||||||||||||||||||
LsbFirst |
1 |
Least significant bit shifted out first |
|||||||||||||||||||||||||||||||||
B | RW |
CPHA |
Serial clock (SCK) phase |
||||||||||||||||||||||||||||||||
Leading |
0 |
Sample on leading edge of clock, shift serial data on trailing edge |
|||||||||||||||||||||||||||||||||
Trailing |
1 |
Sample on trailing edge of clock, shift serial data on leading edge |
|||||||||||||||||||||||||||||||||
C | RW |
CPOL |
Serial clock (SCK) polarity |
||||||||||||||||||||||||||||||||
ActiveHigh |
0 |
Active high |
|||||||||||||||||||||||||||||||||
ActiveLow |
1 |
Active low |
Address offset: 0x560
Sample delay for input serial data on MISO
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
A |
A |
||||||||||||||||||||||||||||||||
Reset 0x00000002 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
RXDELAY |
[7..0] |
Sample delay for input serial data on MISO. The value specifies the number of 64 MHz clock cycles (15.625 ns) delay from the the sampling edge of SCK (leading edge for CONFIG.CPHA = 0, trailing edge for CONFIG.CPHA = 1) until the input serial data is sampled. As en example, if RXDELAY = 0 and CONFIG.CPHA = 0, the input serial data is sampled on the rising edge of SCK. |
Address offset: 0x564
Minimum duration between edge of CSN and edge of SCK and minimum duration CSN must stay high between transactions
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
A |
A |
A |
A |
A |
A |
A |
|||||||||||||||||||||||||||
Reset 0x00000002 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
CSNDUR |
[0xFF..0] |
Minimum duration between edge of CSN and edge of SCK and minimum duration CSN must stay high between transactions. The value is specified in number of 64 MHz clock cycles (15.625 ns). |
Address offset: 0x568
Polarity of CSN output
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
CSNPOL |
Polarity of CSN output |
||||||||||||||||||||||||||||||||
LOW |
0 |
Active low (idle state high) |
|||||||||||||||||||||||||||||||||
HIGH |
1 |
Active high (idle state low) |
Address offset: 0x56C
Pin select for DCX signal
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
C |
B |
A |
A |
A |
A |
A |
||||||||||||||||||||||||||||
Reset 0xFFFFFFFF | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
PIN |
[0..31] |
Pin number |
|||||||||||||||||||||||||||||||
B | RW |
PORT |
[0..1] |
Port number |
|||||||||||||||||||||||||||||||
C | RW |
CONNECT |
Connection |
||||||||||||||||||||||||||||||||
Disconnected |
1 |
Disconnect |
|||||||||||||||||||||||||||||||||
Connected |
0 |
Connect |
Address offset: 0x570
DCX configuration
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
A |
A |
A |
|||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
DCXCNT |
0x0..0xF |
This register specifies the number of command bytes preceding the data bytes. The PSEL.DCX line will be low during transmission of command bytes and high during transmission of data bytes. Value 0xF indicates that all bytes are command bytes. |
Address offset: 0x5C0
Byte transmitted after TXD.MAXCNT bytes have been transmitted in the case when RXD.MAXCNT is greater than TXD.MAXCNT
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID | A | A | A | A | A | A | A | A | |||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
ORC |
Byte transmitted after TXD.MAXCNT bytes have been transmitted in the case when RXD.MAXCNT is greater than TXD.MAXCNT. |
Symbol | Description | Min. | Typ. | Max. | Units | ||||
---|---|---|---|---|---|---|---|---|---|
fSPIM |
Bit rates for SPIM1 |
32 | Mbps | ||||||
tSPIM,START |
Time from START task to transmission started |
1 | µs | ||||||
tSPIM,CSCK |
SCK period |
31.25 | ns | ||||||
tSPIM,RSCK,LD |
SCK rise time, standard drive2 |
tRF,25pF | |||||||
tSPIM,RSCK,HD |
SCK rise time, high drive2 |
tHRF,25pF | |||||||
tSPIM,FSCK,LD |
SCK fall time, standard drive2 |
tRF,25pF | |||||||
tSPIM,FSCK,HD |
SCK fall time, high drive2 |
tHRF,25pF | |||||||
tSPIM,WHSCK |
SCK high time2 |
(tCSCK/2) – tRSCK | |||||||
tSPIM,WLSCK |
SCK low time2 |
(tCSCK/2) – tFSCK | |||||||
tSPIM,SUMI |
MISO to CLK edge setup time |
19 | ns | ||||||
tSPIM,HMI |
CLK edge to MISO hold time |
18 | ns | ||||||
tSPIM,VMO |
CLK edge to MOSI valid, SCK frequency ≤ 8 MHz |
59 | ns | ||||||
tSPIM,VMO,HS |
CLK edge to MOSI valid, SCK frequency > 8 MHz |
8 | ns | ||||||
tSPIM,HMO |
MOSI hold time after CLK edge |
20 | ns |