The NFCT peripheral is an implementation of an NFC Forum compliant listening device NFC-A.
With appropriate software, the NFCT peripheral can be used as the listening device NFC-A as specified by the NFC Forum.
Listed here are the main features for the NFCT peripheral:
The NFCT peripheral contains a 13.56 MHz AM receiver and a 13.56 MHz load modulator with 106 kbps data rate as defined by the NFC Forum.
When transmitting, the frame data will be transferred directly from RAM and transmitted with configurable frame type and delay timing. The system will be notified by an event whenever a complete frame is received or sent. The received frames will be automatically disassembled and the data part of the frame transferred to RAM.
The NFCT peripheral also supports the collision detection and resolution ("anticollision") as defined by the NFC Forum.
Wake-on-field is supported in SENSE mode while the device is either in System OFF or System ON mode. When the antenna enters an NFC field, an event will be triggered notifying the system to activate the NFCT functionality for incoming frames. In System ON, if the energy detected at the antenna increases beyond a threshold value, the module will generate a FIELDDETECTED event. When the strength of the field no longer supports NFC communication, the module will generate a FIELDLOST event. For the Low Power Field Detect threshold values, refer to NFCT Electrical Specification.
In System OFF, the NFCT Low Power Field Detect function can wake the system up through a reset. See RESETREAS for more information on how to detect a wakeup from NFCT.
If the system is put into System OFF mode while a field is already present, the NFCT Low Power Field Detect function will wake the system up right away and generate a reset.
The HFXO must be running before the NFCT peripheral goes into ACTIVATED state. Note that the NFCT peripheral calibration is automatically done on ACTIVATE task. The HFXO can be turned off when the NFCT peripheral goes into SENSE mode. The shortcut FIELDDETECTED_ACTIVATE can be used when the HFXO is already running while in SENSE mode.
Outgoing data will be collected from RAM with the EasyDMA function and assembled according to theTXD.FRAMECONFIG register. Incoming data will be disassembled according to the RXD.FRAMECONFIG register and the data section in the frame will be written to RAM via the EasyDMA function.
The NFCT peripheral includes a frame timing controller that can be used to accurately control the inter-frame delay between the incoming frame and a corresponding outgoing frame. It also includes optional CRC functionality.
Tasks and events are used to control the operating state of the peripheral. The module can change state by triggering a task, or when specific operations are finalized. Events and tasks allow software to keep track of and change the current state.
See NFCT block diagram and NFCT state diagram, automatic collision resolution enabled for more information. See NFC Forum, NFC Activity Technical Specification for description on NFCT operating states.
NFCT uses two pins to connect the antenna and these pins are shared with GPIOs.
The PROTECT field in the NFCPINS register in UICR defines the usage of these pins and their protection level against excessive voltages. The content of the NFCPINS register is reloaded at every reset. See Pin assignments for the pins used by the NFCT peripheral.
When NFCPINS.PROTECT=NFC, a protection circuit will be enabled on the dedicated pins, preventing the chip from being damaged in the presence of a strong NFC field. The protection circuit will short the two pins together if voltage difference exceeds approximately 2V. The GPIO function on those pins will also be disabled.
When NFCPINS.PROTECT=Disabled, the device will not be protected against strong NFC field damages caught by a connected NFCT antenna, and the NFCT peripheral will not operate as expected, as it will never leave the DISABLE state.
The pins dedicated to the NFCT antenna function will have some limitation when the pins are configured for normal GPIO operation. The pin capacitance will be higher on those (refer to CPAD_NFC in the Electrical Specification of GPIO — General purpose input/output), and some increased leakage current between the two pins is to be expected if they are used in GPIO mode, and are driven to different logical values. To save power, the two pins should always be set to the same logical value whenever entering one of the device power saving modes. For details, refer to INFC_LEAK in the Electrical Specification of GPIO — General purpose input/output.
The NFCT peripheral implements EasyDMA for reading and writing of data packets from and to the Data RAM.
The NFCT EasyDMA utilizes a pointer called PACKETPTR for receiving and transmitting packets.
The NFCT peripheral uses EasyDMA to read or write RAM, but not both at the same time. The event RXFRAMESTART indicates that the EasyDMA has started writing to the RAM for a receive frame and the event RXFRAMEND indicates that the EasyDMA has completed writing to the RAM. Similarly, the event TXFRAMESTART indicates that the EasyDMA has started reading from the RAM for a transmit frame and the event TXFRAMEND indicates that the EasyDMA has completed reading from the RAM. If a transmit and a receive operation is issued at the same time, the transmit operation would be prioritized.
Starting a transmit operation while the EasyDMA is writing a receive frame to the RAM will result in unpredictable behavior. Starting an EasyDMA operation when there is an ongoing EasyDMA operation may result in unpredictable behavior. It is recommended to wait for the TXFRAMEEND or RXFRAMEEND event for the ongoing transmit or receive before starting a new receive or transmit operation.
The MAXLEN register determines the maximum number of bytes that can be read from or written to the RAM. This feature can be used to ensure that the NFCT peripheral does not overwrite, or read beyond, the RAM assigned to a packet. Note that if the RXD.AMOUNT or TXD.AMOUNT register indicates longer data packets than set in MAXLEN, the frames sent to or received from the physical layer will be incomplete. In that situation, in RX, the OVERRUN bit in the FRAMESTATUS.RX register will be set and an RXERROR event will be triggered.
Only sending task ENABLERXDATA ensures that a new value in PACKETPTR pointing to the RX buffer in Data RAM is taken into account.
If PACKETPTR is not pointing to the Data RAM region, an EasyDMA transfer may result in a hard fault or RAM corruption. For more information about the different memory regions, see Chapter Memory.
The NFCT peripherals normally do alternative receive and transmit frames. Therefore, to prepare for the next frame, the PACKETPTR, MAXLEN, TXD.FRAMECONFIG and TXD.AMOUNT can be updated while the receive is in progress, and, similarly, the PACKETPTR, MAXLEN and RXD.FRAMECONFIG can be updated while the transmit is in progress. They can be updated and prepared for the next NFC frame immediately after the STARTED event of the current frame has been received. Updating the TXD.FRAMECONFIG and TXD.AMOUNT during the current transmit frame or updating RXD.FRAMECONFIG during current receive frame may cause unpredictable behaviour.
In accordance with NFC Forum, NFC Digital Protocol Technical Specification, the least significant bit (LSB) from the least significant byte (LSByte) is sent on air first. The bytes are stored in increasing order, starting at the lowest address in the EasyDMA buffer in RAM.
The NFCT peripheral implements a frame assembler in hardware.
When the NFCT peripheral is in the ACTIVE_A state, the software can decide to enter RX or TX mode. For RX, see Frame disassembler. For TX, the software must indicate the address of the source buffer in Data RAM and its size through programming the PACKETPTR and MAXLEN registers respectively, then issuing a STARTTX task.
MAXLEN must be set so that it matches the size of the frame to be sent.
The STARTED event indicates that the PACKETPTR and MAXLEN registers have been captured by the frame assembler EasyDMA.
When asserting the STARTTX task, the frame assembler module will start reading TXD.AMOUNT.TXDATABYTES bytes (plus one additional byte if TXD.AMOUNT.TXDATABITS > 0) from the RAM position set by the PACKETPTR.
The NFCT peripheral transmits the data as read from RAM, adding framing and the CRC calculated on the fly if set in TXD.FRAMECONFIG. The NFCT peripheral will take (8*TXD.AMOUNT.TXDATABYTES + TXD.AMOUNT.TXDATABITS) bits and assemble a frame according to the settings in TXD.FRAMECONFIG. Both short frames, standard frames, and bit-oriented SDD frames as specified in the NFC Forum, NFC Digital Protocol Technical Specification can be assembled by the correct setting of the TXD.FRAMECONFIG register.
The bytes will be transmitted on air in the same order as they are read from RAM with a rising bit order within each byte, least significant bit (LSB) first. That is, b0 will be transmitted on air before b1, and so on. The bits read from RAM will be coded into symbols as defined in the NFC Forum, NFC Digital Protocol Technical Specification.
The frame assembler can be configured in TXD.FRAMECONFIG to add SoF symbol, calculate and add parity bits, and calculate and add CRC to the data read from RAM when assembling the frame. The total frame will then be longer than what is defined by TXD.AMOUNT.TXDATABYTES. TXDATABITS. DISCARDMODE will select if the first bits in the first byte read from RAM or the last bits in the last byte read from RAM will be discarded if TXD.AMOUNT.TXDATABITS are not equal to zero. Note that if TXD.FRAMECONFIG.PARITY = Parity and TXD.FRAMECONFIG.DISCARDMODE=DiscardStart, a parity bit will be included after the non-complete first byte. No parity will be added after a non-complete last byte.
The frame assemble operation is illustrated in Frame assemble illustration for different settings in TXD.FRAMECONFIG. All shaded bit fields are added by the frame assembler. Some of these bits are optional and appearances are configured in TXD.FRAMECONFIG. Note that the frames illustrated do not necessarily comply with the NFC specification. The figure is only to illustrate the behavior of the NFCT peripheral.
The accurate timing for transmitting the frame on air is set using the frame timing controller settings.
The NFCT peripheral implements a frame disassembler in hardware.
When the NFCT peripheral is in the ACTIVE_A state, the software can decide to enter RX or TX mode. For TX, see Frame assembler. For RX, the software must indicate the address and size of the destination buffer in Data RAM through programming the PACKETPTR and MAXLEN registers before issuing an ENABLERXDATA task.
The STARTED event indicates that the PACKETPTR and MAXLEN registers have been captured by the frame disassembler EasyDMA.
When an incoming frame starts, the RXFRAMESTART event will get issued and data will be written to the buffer in Data RAM. The frame disassembler will verify and remove any parity bits, start of frame (SoF) and end of frame (EoF) symbols on the fly based on RXD.FRAMECONFIG register configuration. It will, however, verify and transfer the CRC bytes into RAM, if the CRC is enabled through RXD.FRAMECONFIG.
When an EoF symbol is detected, the NFCT peripheral will assert the RXFRAMEEND event and write the RXD.AMOUNT register to indicate numbers of received bytes and bits in the data packet. The module does not interpret the content of the data received from the remote NFC device, except for SoF, EoF, parity, and CRC checking, as described above. The frame disassemble operation is illustrated below.
Per NFC specification, the time between EoF to the next SoF can be as short as 86 μs, and thefore care must be taken that PACKETPTR and MAXLEN are ready and ENABLERXDATA is issued on time after the end of previous frame. The use of a PPI shortcut from TXFRAMEEND to ENABLERXDATA is recommended.
The NFCT peripheral includes a frame timing controller that continuously keeps track of the number of the 13.56 MHz RF carrier clock periods since the end of the EoF of the last received frame.
The NFCT peripheral can be programmed to send a responding frame within a time window or at an exact count of RF carrier periods. In case of FRAMEDELAYMODE = Window, a STARTTX task triggered before the frame timing controller counter is equal to FRAMEDELAYMIN will force the transmission to halt until the counter is equal to FRAMEDELAYMIN. If the counter is within FRAMEDELAYMIN and FRAMEDELAYMAX when the STARTTX task is triggered, the NFCT peripheral will start the transmission straight away. In case of FRAMEDELAYMODE = ExactVal, a STARTTX task triggered before the frame delay counter is equal to FRAMEDELAYMAX will halt the actual transmission start until the counter is equal to FRAMEDELAYMAX.
In case of FRAMEDELAYMODE = WindowGrid, the behaviour is similar to the FRAMEDELAYMODE = Window, but the actual transmission between FRAMEDELAYMIN and FRAMEDELAYMAX starts on a bit grid as defined for NFC-A Listen frames (slot duration of 128 RF carrier periods).
An ERROR event (with FRAMEDELAYTIMEOUT cause in ERRORSTATUS) will be asserted if the frame timing controller counter reaches FRAMEDELAYMAX without any STARTTX task triggered. This may happen even when the response is not required as per NFC Forum, NFC Digital Protocol Technical Specification. Any commands handled by the automatic collision resolution that don't involve a response being generated may also result in an ERROR event (with FRAMEDELAYTIMEOUT cause in ERRORSTATUS). The FRAMEDELAYMIN and FRAMEDELAYMAX values shall only be updated before the STARTTX task is triggered. Failing to do so may cause unpredictable behaviour.
The frame timing controller operation is illustrated in Frame timing controller (FRAMEDELAYMODE=Window). The frame timing controller automatically adjusts the frame timing counter based on the last received data bit according to NFC-A technology in the NFC Forum, NFC Digital Protocol Technical Specification.
The NFCT peripheral implements an automatic collision resolution function as defined by the NFC Forum.
Automatic collision resolution is enabled by default, and it is recommended that the feature is used since it is power efficient and reduces the complexity of software handling the collision resolution sequence. This feature can be disabled through the MODE field in the AUTOCOLRESCONFIG register. When the automatic collision resolution is disabled, all commands will be sent over EasyDMA as defined in frame disassembler.
A pre-defined set of registers, NFC.TAGHEADER0..3, containing a valid NFCID1 value, is available in FICR and can be used by software to populate the NFCID1_3RD_LAST, NFCID1_2ND_LAST, and NFCID1_LAST registers.
NFCID1 byte allocation (top sent first on air) explains the position of the ID bytes in NFCID1_3RD_LAST, NFCID1_2ND_LAST, and NFCID1_LAST, depending on the ID size, and as compared to the definition used in the NFC Forum, NFC Digital Protocol Technical Specification.
ID = 4 bytes | ID = 7 bytes | ID = 10 bytes | |
---|---|---|---|
NFCID1_Q | nfcid10 | ||
NFCID1_R | nfcid11 | ||
NFCID1_S | nfcid12 | ||
NFCID1_T | nfcid10 | nfcid13 | |
NFCID1_U | nfcid11 | nfcid14 | |
NFCID1_V | nfcid12 | nfcid15 | |
NFCID1_W | nfcid10 | nfcid13 | nfcid16 |
NFCID1_X | nfcid11 | nfcid14 | nfcid17 |
NFCID1_Y | nfcid12 | nfcid15 | nfcid18 |
NFCID1_Z | nfcid13 | nfcid16 | nfcid19 |
The hardware implementation can handle the states from IDLE to ACTIVE_A automatically as defined in the NFC Forum, NFC Activity Technical Specification, and the other states are to be handled by software. The software keeps track of the state through events. The collision resolution will trigger an AUTOCOLRESSTARTED event when it has started. Reaching the ACTIVE_A state is indicated by the SELECTED event.
If collision resolution fails, a COLLISION event is triggered. Note that errors occurring during automatic collision resolution may also cause ERROR and/or RXERROR events to be generated. Other events may also get generated. It is recommended that the software ignores any event except COLLISION, SELECTED and FIELDLOST during automatic collision resolution. Software shall also make sure that any unwanted SHORT or PPI shortcut is disabled during automatic collision resolution.
The automatic collision resolution will be restarted, if the packets are received with CRC or parity errors while in ACTIVE_A state. The automatic collision resolution feature can be disabled while in ACTIVE_A state to avoid this.
The SLP_REQ is automatically handled by the NFCT peripheral when the automatic collision resolution is enabled. However, this results in an ERROR event (with FRAMEDELAYTIMEOUT cause in ERRORSTATUS) since the SLP_REQ has no response. This error must be ignored until the SELECTED event is triggered and this error should be cleared by the software when the SELECTED event is triggered.
In ACTIVATED state, an amplitude regulator will adjust the voltage swing on the antenna pins to a value that is within the Vswing limit.
Refer to NFCT Electrical Specification.
The NFCT antenna coil must be connected differential between NFC1 and NFC2 pins of the device.
Two external capacitors should be used to tune the resonance of the antenna circuit to 13.56 MHz.
The required tuning capacitor value is given by the below equations:
An antenna inductance of Lant = 2 μH will give tuning capacitors in the range of 130 pF on each pin. The total capacitance on NFC1 and NFC2 must be matched.
If the antenna is exposed to a strong NFC field, current may flow in the opposite direction on the supply due to parasitic diodes and ESD structures.
If the battery used does not tolerate return current, a series diode must be placed between the battery and the device in order to protect the battery.
NFC Forum, NFC Analog Specification version 1.0, www.nfc-forum.org
NFC Forum, NFC Digital Protocol Technical Specification version 1.1, www.nfc-forum.org
NFC Forum, NFC Activity Technical Specification version 1.1, www.nfc-forum.org
Base address | Peripheral | Instance | Description | Configuration | |
---|---|---|---|---|---|
0x40005000 | NFCT | NFCT |
Near field communication tag |
Register | Offset | Description | |
---|---|---|---|
TASKS_ACTIVATE | 0x000 |
Activate NFCT peripheral for incoming and outgoing frames, change state to activated |
|
TASKS_DISABLE | 0x004 |
Disable NFCT peripheral |
|
TASKS_SENSE | 0x008 |
Enable NFC sense field mode, change state to sense mode |
|
TASKS_STARTTX | 0x00C |
Start transmission of an outgoing frame, change state to transmit |
|
TASKS_ENABLERXDATA | 0x01C |
Initializes the EasyDMA for receive. |
|
TASKS_GOIDLE | 0x024 |
Force state machine to IDLE state |
|
TASKS_GOSLEEP | 0x028 |
Force state machine to SLEEP_A state |
|
EVENTS_READY | 0x100 |
The NFCT peripheral is ready to receive and send frames |
|
EVENTS_FIELDDETECTED | 0x104 |
Remote NFC field detected |
|
EVENTS_FIELDLOST | 0x108 |
Remote NFC field lost |
|
EVENTS_TXFRAMESTART | 0x10C |
Marks the start of the first symbol of a transmitted frame |
|
EVENTS_TXFRAMEEND | 0x110 |
Marks the end of the last transmitted on-air symbol of a frame |
|
EVENTS_RXFRAMESTART | 0x114 |
Marks the end of the first symbol of a received frame |
|
EVENTS_RXFRAMEEND | 0x118 |
Received data has been checked (CRC, parity) and transferred to RAM, and EasyDMA has ended accessing the RX buffer |
|
EVENTS_ERROR | 0x11C |
NFC error reported. The ERRORSTATUS register contains details on the source of the error. |
|
EVENTS_RXERROR | 0x128 |
NFC RX frame error reported. The FRAMESTATUS.RX register contains details on the source of the error. |
|
EVENTS_ENDRX | 0x12C |
RX buffer (as defined by PACKETPTR and MAXLEN) in Data RAM full. |
|
EVENTS_ENDTX | 0x130 |
Transmission of data in RAM has ended, and EasyDMA has ended accessing the TX buffer |
|
EVENTS_AUTOCOLRESSTARTED | 0x138 |
Auto collision resolution process has started |
|
EVENTS_COLLISION | 0x148 |
NFC auto collision resolution error reported. |
|
EVENTS_SELECTED | 0x14C |
NFC auto collision resolution successfully completed |
|
EVENTS_STARTED | 0x150 |
EasyDMA is ready to receive or send frames. |
|
SHORTS | 0x200 |
Shortcuts between local events and tasks |
|
INTEN | 0x300 |
Enable or disable interrupt |
|
INTENSET | 0x304 |
Enable interrupt |
|
INTENCLR | 0x308 |
Disable interrupt |
|
ERRORSTATUS | 0x404 |
NFC Error Status register |
|
FRAMESTATUS.RX | 0x40C |
Result of last incoming frame |
|
NFCTAGSTATE | 0x410 |
NfcTag state register |
|
SLEEPSTATE | 0x420 |
Sleep state during automatic collision resolution |
|
FIELDPRESENT | 0x43C |
Indicates the presence or not of a valid field |
|
FRAMEDELAYMIN | 0x504 |
Minimum frame delay |
|
FRAMEDELAYMAX | 0x508 |
Maximum frame delay |
|
FRAMEDELAYMODE | 0x50C |
Configuration register for the Frame Delay Timer |
|
PACKETPTR | 0x510 |
Packet pointer for TXD and RXD data storage in Data RAM |
|
MAXLEN | 0x514 |
Size of the RAM buffer allocated to TXD and RXD data storage each |
|
TXD.FRAMECONFIG | 0x518 |
Configuration of outgoing frames |
|
TXD.AMOUNT | 0x51C |
Size of outgoing frame |
|
RXD.FRAMECONFIG | 0x520 |
Configuration of incoming frames |
|
RXD.AMOUNT | 0x524 |
Size of last incoming frame |
|
NFCID1_LAST | 0x590 |
Last NFCID1 part (4, 7 or 10 bytes ID) |
|
NFCID1_2ND_LAST | 0x594 |
Second last NFCID1 part (7 or 10 bytes ID) |
|
NFCID1_3RD_LAST | 0x598 |
Third last NFCID1 part (10 bytes ID) |
|
AUTOCOLRESCONFIG | 0x59C |
Controls the auto collision resolution function. This setting must be done before the NFCT peripheral is activated. |
|
SENSRES | 0x5A0 |
NFC-A SENS_RES auto-response settings |
|
SELRES | 0x5A4 |
NFC-A SEL_RES auto-response settings |
Address offset: 0x000
Activate NFCT peripheral for incoming and outgoing frames, change state to activated
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | W |
TASKS_ACTIVATE |
Activate NFCT peripheral for incoming and outgoing frames, change state to activated |
||||||||||||||||||||||||||||||||
Trigger |
1 |
Trigger task |
Address offset: 0x004
Disable NFCT peripheral
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | W |
TASKS_DISABLE |
Disable NFCT peripheral |
||||||||||||||||||||||||||||||||
Trigger |
1 |
Trigger task |
Address offset: 0x008
Enable NFC sense field mode, change state to sense mode
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | W |
TASKS_SENSE |
Enable NFC sense field mode, change state to sense mode |
||||||||||||||||||||||||||||||||
Trigger |
1 |
Trigger task |
Address offset: 0x00C
Start transmission of an outgoing frame, change state to transmit
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | W |
TASKS_STARTTX |
Start transmission of an outgoing frame, change state to transmit |
||||||||||||||||||||||||||||||||
Trigger |
1 |
Trigger task |
Address offset: 0x01C
Initializes the EasyDMA for receive.
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | W |
TASKS_ENABLERXDATA |
Initializes the EasyDMA for receive. |
||||||||||||||||||||||||||||||||
Trigger |
1 |
Trigger task |
Address offset: 0x024
Force state machine to IDLE state
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | W |
TASKS_GOIDLE |
Force state machine to IDLE state |
||||||||||||||||||||||||||||||||
Trigger |
1 |
Trigger task |
Address offset: 0x028
Force state machine to SLEEP_A state
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | W |
TASKS_GOSLEEP |
Force state machine to SLEEP_A state |
||||||||||||||||||||||||||||||||
Trigger |
1 |
Trigger task |
Address offset: 0x100
The NFCT peripheral is ready to receive and send frames
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
EVENTS_READY |
The NFCT peripheral is ready to receive and send frames |
||||||||||||||||||||||||||||||||
NotGenerated |
0 |
Event not generated |
|||||||||||||||||||||||||||||||||
Generated |
1 |
Event generated |
Address offset: 0x104
Remote NFC field detected
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
EVENTS_FIELDDETECTED |
Remote NFC field detected |
||||||||||||||||||||||||||||||||
NotGenerated |
0 |
Event not generated |
|||||||||||||||||||||||||||||||||
Generated |
1 |
Event generated |
Address offset: 0x108
Remote NFC field lost
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
EVENTS_FIELDLOST |
Remote NFC field lost |
||||||||||||||||||||||||||||||||
NotGenerated |
0 |
Event not generated |
|||||||||||||||||||||||||||||||||
Generated |
1 |
Event generated |
Address offset: 0x10C
Marks the start of the first symbol of a transmitted frame
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
EVENTS_TXFRAMESTART |
Marks the start of the first symbol of a transmitted frame |
||||||||||||||||||||||||||||||||
NotGenerated |
0 |
Event not generated |
|||||||||||||||||||||||||||||||||
Generated |
1 |
Event generated |
Address offset: 0x110
Marks the end of the last transmitted on-air symbol of a frame
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
EVENTS_TXFRAMEEND |
Marks the end of the last transmitted on-air symbol of a frame |
||||||||||||||||||||||||||||||||
NotGenerated |
0 |
Event not generated |
|||||||||||||||||||||||||||||||||
Generated |
1 |
Event generated |
Address offset: 0x114
Marks the end of the first symbol of a received frame
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
EVENTS_RXFRAMESTART |
Marks the end of the first symbol of a received frame |
||||||||||||||||||||||||||||||||
NotGenerated |
0 |
Event not generated |
|||||||||||||||||||||||||||||||||
Generated |
1 |
Event generated |
Address offset: 0x118
Received data has been checked (CRC, parity) and transferred to RAM, and EasyDMA has ended accessing the RX buffer
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
EVENTS_RXFRAMEEND |
Received data has been checked (CRC, parity) and transferred to RAM, and EasyDMA has ended accessing the RX buffer |
||||||||||||||||||||||||||||||||
NotGenerated |
0 |
Event not generated |
|||||||||||||||||||||||||||||||||
Generated |
1 |
Event generated |
Address offset: 0x11C
NFC error reported. The ERRORSTATUS register contains details on the source of the error.
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
EVENTS_ERROR |
NFC error reported. The ERRORSTATUS register contains details on the source of the error. |
||||||||||||||||||||||||||||||||
NotGenerated |
0 |
Event not generated |
|||||||||||||||||||||||||||||||||
Generated |
1 |
Event generated |
Address offset: 0x128
NFC RX frame error reported. The FRAMESTATUS.RX register contains details on the source of the error.
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
EVENTS_RXERROR |
NFC RX frame error reported. The FRAMESTATUS.RX register contains details on the source of the error. |
||||||||||||||||||||||||||||||||
NotGenerated |
0 |
Event not generated |
|||||||||||||||||||||||||||||||||
Generated |
1 |
Event generated |
Address offset: 0x12C
RX buffer (as defined by PACKETPTR and MAXLEN) in Data RAM full.
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
EVENTS_ENDRX |
RX buffer (as defined by PACKETPTR and MAXLEN) in Data RAM full. |
||||||||||||||||||||||||||||||||
NotGenerated |
0 |
Event not generated |
|||||||||||||||||||||||||||||||||
Generated |
1 |
Event generated |
Address offset: 0x130
Transmission of data in RAM has ended, and EasyDMA has ended accessing the TX buffer
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
EVENTS_ENDTX |
Transmission of data in RAM has ended, and EasyDMA has ended accessing the TX buffer |
||||||||||||||||||||||||||||||||
NotGenerated |
0 |
Event not generated |
|||||||||||||||||||||||||||||||||
Generated |
1 |
Event generated |
Address offset: 0x138
Auto collision resolution process has started
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
EVENTS_AUTOCOLRESSTARTED |
Auto collision resolution process has started |
||||||||||||||||||||||||||||||||
NotGenerated |
0 |
Event not generated |
|||||||||||||||||||||||||||||||||
Generated |
1 |
Event generated |
Address offset: 0x148
NFC auto collision resolution error reported.
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
EVENTS_COLLISION |
NFC auto collision resolution error reported. |
||||||||||||||||||||||||||||||||
NotGenerated |
0 |
Event not generated |
|||||||||||||||||||||||||||||||||
Generated |
1 |
Event generated |
Address offset: 0x14C
NFC auto collision resolution successfully completed
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
EVENTS_SELECTED |
NFC auto collision resolution successfully completed |
||||||||||||||||||||||||||||||||
NotGenerated |
0 |
Event not generated |
|||||||||||||||||||||||||||||||||
Generated |
1 |
Event generated |
Address offset: 0x150
EasyDMA is ready to receive or send frames.
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
EVENTS_STARTED |
EasyDMA is ready to receive or send frames. |
||||||||||||||||||||||||||||||||
NotGenerated |
0 |
Event not generated |
|||||||||||||||||||||||||||||||||
Generated |
1 |
Event generated |
Address offset: 0x200
Shortcuts between local events and tasks
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
F |
B |
A |
||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
FIELDDETECTED_ACTIVATE |
Shortcut between event FIELDDETECTED and task ACTIVATE |
||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable shortcut |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Enable shortcut |
|||||||||||||||||||||||||||||||||
B | RW |
FIELDLOST_SENSE |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable shortcut |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Enable shortcut |
|||||||||||||||||||||||||||||||||
F | RW |
TXFRAMEEND_ENABLERXDATA |
Shortcut between event TXFRAMEEND and task ENABLERXDATA |
||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable shortcut |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Enable shortcut |
Address offset: 0x300
Enable or disable interrupt
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
T |
S |
R |
N |
M |
L |
K |
H |
G |
F |
E |
D |
C |
B |
A |
||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
READY |
Enable or disable interrupt for event READY |
||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Enable |
|||||||||||||||||||||||||||||||||
B | RW |
FIELDDETECTED |
Enable or disable interrupt for event FIELDDETECTED |
||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Enable |
|||||||||||||||||||||||||||||||||
C | RW |
FIELDLOST |
Enable or disable interrupt for event FIELDLOST |
||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Enable |
|||||||||||||||||||||||||||||||||
D | RW |
TXFRAMESTART |
Enable or disable interrupt for event TXFRAMESTART |
||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Enable |
|||||||||||||||||||||||||||||||||
E | RW |
TXFRAMEEND |
Enable or disable interrupt for event TXFRAMEEND |
||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Enable |
|||||||||||||||||||||||||||||||||
F | RW |
RXFRAMESTART |
Enable or disable interrupt for event RXFRAMESTART |
||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Enable |
|||||||||||||||||||||||||||||||||
G | RW |
RXFRAMEEND |
Enable or disable interrupt for event RXFRAMEEND |
||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Enable |
|||||||||||||||||||||||||||||||||
H | RW |
ERROR |
Enable or disable interrupt for event ERROR |
||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Enable |
|||||||||||||||||||||||||||||||||
K | RW |
RXERROR |
Enable or disable interrupt for event RXERROR |
||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Enable |
|||||||||||||||||||||||||||||||||
L | RW |
ENDRX |
Enable or disable interrupt for event ENDRX |
||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Enable |
|||||||||||||||||||||||||||||||||
M | RW |
ENDTX |
Enable or disable interrupt for event ENDTX |
||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Enable |
|||||||||||||||||||||||||||||||||
N | RW |
AUTOCOLRESSTARTED |
Enable or disable interrupt for event AUTOCOLRESSTARTED |
||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Enable |
|||||||||||||||||||||||||||||||||
R | RW |
COLLISION |
Enable or disable interrupt for event COLLISION |
||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Enable |
|||||||||||||||||||||||||||||||||
S | RW |
SELECTED |
Enable or disable interrupt for event SELECTED |
||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Enable |
|||||||||||||||||||||||||||||||||
T | RW |
STARTED |
Enable or disable interrupt for event STARTED |
||||||||||||||||||||||||||||||||
Disabled |
0 |
Disable |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Enable |
Address offset: 0x304
Enable interrupt
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
T |
S |
R |
N |
M |
L |
K |
H |
G |
F |
E |
D |
C |
B |
A |
||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
READY |
Write '1' to enable interrupt for event READY |
||||||||||||||||||||||||||||||||
Set |
1 |
Enable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
B | RW |
FIELDDETECTED |
Write '1' to enable interrupt for event FIELDDETECTED |
||||||||||||||||||||||||||||||||
Set |
1 |
Enable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
C | RW |
FIELDLOST |
Write '1' to enable interrupt for event FIELDLOST |
||||||||||||||||||||||||||||||||
Set |
1 |
Enable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
D | RW |
TXFRAMESTART |
Write '1' to enable interrupt for event TXFRAMESTART |
||||||||||||||||||||||||||||||||
Set |
1 |
Enable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
E | RW |
TXFRAMEEND |
Write '1' to enable interrupt for event TXFRAMEEND |
||||||||||||||||||||||||||||||||
Set |
1 |
Enable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
F | RW |
RXFRAMESTART |
Write '1' to enable interrupt for event RXFRAMESTART |
||||||||||||||||||||||||||||||||
Set |
1 |
Enable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
G | RW |
RXFRAMEEND |
Write '1' to enable interrupt for event RXFRAMEEND |
||||||||||||||||||||||||||||||||
Set |
1 |
Enable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
H | RW |
ERROR |
Write '1' to enable interrupt for event ERROR |
||||||||||||||||||||||||||||||||
Set |
1 |
Enable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
K | RW |
RXERROR |
Write '1' to enable interrupt for event RXERROR |
||||||||||||||||||||||||||||||||
Set |
1 |
Enable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
L | RW |
ENDRX |
Write '1' to enable interrupt for event ENDRX |
||||||||||||||||||||||||||||||||
Set |
1 |
Enable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
M | RW |
ENDTX |
Write '1' to enable interrupt for event ENDTX |
||||||||||||||||||||||||||||||||
Set |
1 |
Enable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
N | RW |
AUTOCOLRESSTARTED |
Write '1' to enable interrupt for event AUTOCOLRESSTARTED |
||||||||||||||||||||||||||||||||
Set |
1 |
Enable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
R | RW |
COLLISION |
Write '1' to enable interrupt for event COLLISION |
||||||||||||||||||||||||||||||||
Set |
1 |
Enable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
S | RW |
SELECTED |
Write '1' to enable interrupt for event SELECTED |
||||||||||||||||||||||||||||||||
Set |
1 |
Enable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
T | RW |
STARTED |
Write '1' to enable interrupt for event STARTED |
||||||||||||||||||||||||||||||||
Set |
1 |
Enable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
Address offset: 0x308
Disable interrupt
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
T |
S |
R |
N |
M |
L |
K |
H |
G |
F |
E |
D |
C |
B |
A |
||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
READY |
Write '1' to disable interrupt for event READY |
||||||||||||||||||||||||||||||||
Clear |
1 |
Disable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
B | RW |
FIELDDETECTED |
Write '1' to disable interrupt for event FIELDDETECTED |
||||||||||||||||||||||||||||||||
Clear |
1 |
Disable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
C | RW |
FIELDLOST |
Write '1' to disable interrupt for event FIELDLOST |
||||||||||||||||||||||||||||||||
Clear |
1 |
Disable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
D | RW |
TXFRAMESTART |
Write '1' to disable interrupt for event TXFRAMESTART |
||||||||||||||||||||||||||||||||
Clear |
1 |
Disable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
E | RW |
TXFRAMEEND |
Write '1' to disable interrupt for event TXFRAMEEND |
||||||||||||||||||||||||||||||||
Clear |
1 |
Disable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
F | RW |
RXFRAMESTART |
Write '1' to disable interrupt for event RXFRAMESTART |
||||||||||||||||||||||||||||||||
Clear |
1 |
Disable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
G | RW |
RXFRAMEEND |
Write '1' to disable interrupt for event RXFRAMEEND |
||||||||||||||||||||||||||||||||
Clear |
1 |
Disable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
H | RW |
ERROR |
Write '1' to disable interrupt for event ERROR |
||||||||||||||||||||||||||||||||
Clear |
1 |
Disable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
K | RW |
RXERROR |
Write '1' to disable interrupt for event RXERROR |
||||||||||||||||||||||||||||||||
Clear |
1 |
Disable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
L | RW |
ENDRX |
Write '1' to disable interrupt for event ENDRX |
||||||||||||||||||||||||||||||||
Clear |
1 |
Disable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
M | RW |
ENDTX |
Write '1' to disable interrupt for event ENDTX |
||||||||||||||||||||||||||||||||
Clear |
1 |
Disable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
N | RW |
AUTOCOLRESSTARTED |
Write '1' to disable interrupt for event AUTOCOLRESSTARTED |
||||||||||||||||||||||||||||||||
Clear |
1 |
Disable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
R | RW |
COLLISION |
Write '1' to disable interrupt for event COLLISION |
||||||||||||||||||||||||||||||||
Clear |
1 |
Disable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
S | RW |
SELECTED |
Write '1' to disable interrupt for event SELECTED |
||||||||||||||||||||||||||||||||
Clear |
1 |
Disable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
|||||||||||||||||||||||||||||||||
T | RW |
STARTED |
Write '1' to disable interrupt for event STARTED |
||||||||||||||||||||||||||||||||
Clear |
1 |
Disable |
|||||||||||||||||||||||||||||||||
Disabled |
0 |
Read: Disabled |
|||||||||||||||||||||||||||||||||
Enabled |
1 |
Read: Enabled |
Address offset: 0x404
NFC Error Status register
Write a bit to '1' to clear it. Writing '0' has no effect.
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
FRAMEDELAYTIMEOUT |
No STARTTX task triggered before expiration of the time set in FRAMEDELAYMAX |
Address offset: 0x40C
Result of last incoming frame
Write a bit to '1' to clear it. Writing '0' has no effect.
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
C |
B |
A |
||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
CRCERROR |
No valid end of frame (EoF) detected |
||||||||||||||||||||||||||||||||
CRCCorrect |
0 |
Valid CRC detected |
|||||||||||||||||||||||||||||||||
CRCError |
1 |
CRC received does not match local check |
|||||||||||||||||||||||||||||||||
B | RW |
PARITYSTATUS |
Parity status of received frame |
||||||||||||||||||||||||||||||||
ParityOK |
0 |
Frame received with parity OK |
|||||||||||||||||||||||||||||||||
ParityError |
1 |
Frame received with parity error |
|||||||||||||||||||||||||||||||||
C | RW |
OVERRUN |
Overrun detected |
||||||||||||||||||||||||||||||||
NoOverrun |
0 |
No overrun detected |
|||||||||||||||||||||||||||||||||
Overrun |
1 |
Overrun error |
Address offset: 0x410
NfcTag state register
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
A |
A |
||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | R |
NFCTAGSTATE |
NfcTag state |
||||||||||||||||||||||||||||||||
Disabled |
0 |
Disabled or sense |
|||||||||||||||||||||||||||||||||
RampUp |
2 |
RampUp |
|||||||||||||||||||||||||||||||||
Idle |
3 |
Idle |
|||||||||||||||||||||||||||||||||
Receive |
4 |
Receive |
|||||||||||||||||||||||||||||||||
FrameDelay |
5 |
FrameDelay |
|||||||||||||||||||||||||||||||||
Transmit |
6 |
Transmit |
Address offset: 0x420
Sleep state during automatic collision resolution
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | R |
SLEEPSTATE |
Reflects the sleep state during automatic collision resolution. Set to IDLE by a GOIDLE task. Set to SLEEP_A when a valid SLEEP_REQ frame is received or by a GOSLEEP task. |
||||||||||||||||||||||||||||||||
Idle |
0 |
State is IDLE. |
|||||||||||||||||||||||||||||||||
SleepA |
1 |
State is SLEEP_A. |
Address offset: 0x43C
Indicates the presence or not of a valid field
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
B |
A |
|||||||||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | R |
FIELDPRESENT |
Indicates if a valid field is present. Available only in the activated state. |
||||||||||||||||||||||||||||||||
NoField |
0 |
No valid field detected |
|||||||||||||||||||||||||||||||||
FieldPresent |
1 |
Valid field detected |
|||||||||||||||||||||||||||||||||
B | R |
LOCKDETECT |
Indicates if the low level has locked to the field |
||||||||||||||||||||||||||||||||
NotLocked |
0 |
Not locked to field |
|||||||||||||||||||||||||||||||||
Locked |
1 |
Locked to field |
Address offset: 0x504
Minimum frame delay
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
|||||||||||||||||||
Reset 0x00000480 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
FRAMEDELAYMIN |
Minimum frame delay in number of 13.56 MHz clocks |
Address offset: 0x508
Maximum frame delay
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
|||||||||||||||
Reset 0x00001000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
FRAMEDELAYMAX |
Maximum frame delay in number of 13.56 MHz clocks |
Address offset: 0x50C
Configuration register for the Frame Delay Timer
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
A |
|||||||||||||||||||||||||||||||||
Reset 0x00000001 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
FRAMEDELAYMODE |
Configuration register for the Frame Delay Timer |
||||||||||||||||||||||||||||||||
FreeRun |
0 |
Transmission is independent of frame timer and will start when the STARTTX task is triggered. No timeout. |
|||||||||||||||||||||||||||||||||
Window |
1 |
Frame is transmitted between FRAMEDELAYMIN and FRAMEDELAYMAX |
|||||||||||||||||||||||||||||||||
ExactVal |
2 |
Frame is transmitted exactly at FRAMEDELAYMAX |
|||||||||||||||||||||||||||||||||
WindowGrid |
3 |
Frame is transmitted on a bit grid between FRAMEDELAYMIN and FRAMEDELAYMAX |
Address offset: 0x510
Packet pointer for TXD and RXD data storage in Data RAM
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
A |
|||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
PTR |
Packet pointer for TXD and RXD data storage in Data RAM. This address is a byte-aligned RAM address. Note: See the memory chapter for details about which memories are available for EasyDMA.
|
Address offset: 0x514
Size of the RAM buffer allocated to TXD and RXD data storage each
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
A |
A |
A |
A |
A |
A |
A |
A |
||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
MAXLEN |
[0..257] |
Size of the RAM buffer allocated to TXD and RXD data storage each |
Address offset: 0x518
Configuration of outgoing frames
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
D |
C |
B |
A |
|||||||||||||||||||||||||||||||
Reset 0x00000017 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 1 | 1 | 1 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
PARITY |
Indicates if parity is added to the frame |
||||||||||||||||||||||||||||||||
NoParity |
0 |
Parity is not added to TX frames |
|||||||||||||||||||||||||||||||||
Parity |
1 |
Parity is added to TX frames |
|||||||||||||||||||||||||||||||||
B | RW |
DISCARDMODE |
Discarding unused bits at start or end of a frame |
||||||||||||||||||||||||||||||||
DiscardEnd |
0 |
Unused bits are discarded at end of frame (EoF) |
|||||||||||||||||||||||||||||||||
DiscardStart |
1 |
Unused bits are discarded at start of frame (SoF) |
|||||||||||||||||||||||||||||||||
C | RW |
SOF |
Adding SoF or not in TX frames |
||||||||||||||||||||||||||||||||
NoSoF |
0 |
SoF symbol not added |
|||||||||||||||||||||||||||||||||
SoF |
1 |
SoF symbol added |
|||||||||||||||||||||||||||||||||
D | RW |
CRCMODETX |
CRC mode for outgoing frames |
||||||||||||||||||||||||||||||||
NoCRCTX |
0 |
CRC is not added to the frame |
|||||||||||||||||||||||||||||||||
CRC16TX |
1 |
16 bit CRC added to the frame based on all the data read from RAM that is used in the frame |
Address offset: 0x51C
Size of outgoing frame
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
B |
B |
B |
B |
B |
B |
B |
B |
B |
A |
A |
A |
|||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
TXDATABITS |
[0..7] |
Number of bits in the last or first byte read from RAM that shall be included in the frame (excluding parity bit). The DISCARDMODE field in FRAMECONFIG.TX selects if unused bits is discarded at the start or at the end of a frame. A value of 0 data bytes and 0 data bits is invalid. |
|||||||||||||||||||||||||||||||
B | RW |
TXDATABYTES |
[0..257] |
Number of complete bytes that shall be included in the frame, excluding CRC, parity and framing |
Address offset: 0x520
Configuration of incoming frames
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
C |
B |
A |
||||||||||||||||||||||||||||||||
Reset 0x00000015 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 1 | 0 | 1 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
PARITY |
Indicates if parity expected in RX frame |
||||||||||||||||||||||||||||||||
NoParity |
0 |
Parity is not expected in RX frames |
|||||||||||||||||||||||||||||||||
Parity |
1 |
Parity is expected in RX frames |
|||||||||||||||||||||||||||||||||
B | RW |
SOF |
SoF expected or not in RX frames |
||||||||||||||||||||||||||||||||
NoSoF |
0 |
SoF symbol is not expected in RX frames |
|||||||||||||||||||||||||||||||||
SoF |
1 |
SoF symbol is expected in RX frames |
|||||||||||||||||||||||||||||||||
C | RW |
CRCMODERX |
CRC mode for incoming frames |
||||||||||||||||||||||||||||||||
NoCRCRX |
0 |
CRC is not expected in RX frames |
|||||||||||||||||||||||||||||||||
CRC16RX |
1 |
Last 16 bits in RX frame is CRC, CRC is checked and CRCSTATUS updated |
Address offset: 0x524
Size of last incoming frame
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
B |
B |
B |
B |
B |
B |
B |
B |
B |
A |
A |
A |
|||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | R |
RXDATABITS |
Number of bits in the last byte in the frame, if less than 8 (including CRC, but excluding parity and SoF/EoF framing). Frames with 0 data bytes and less than 7 data bits are invalid and are not received properly. |
||||||||||||||||||||||||||||||||
B | R |
RXDATABYTES |
Number of complete bytes received in the frame (including CRC, but excluding parity and SoF/EoF framing) |
Address offset: 0x590
Last NFCID1 part (4, 7 or 10 bytes ID)
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
D |
D |
D |
D |
D |
D |
D |
D |
C |
C |
C |
C |
C |
C |
C |
C |
B |
B |
B |
B |
B |
B |
B |
B |
A |
A |
A |
A |
A |
A |
A |
A |
|||
Reset 0x00006363 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 0 | 0 | 0 | 1 | 1 | 0 | 1 | 1 | 0 | 0 | 0 | 1 | 1 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
NFCID1_Z |
NFCID1 byte Z (very last byte sent) |
||||||||||||||||||||||||||||||||
B | RW |
NFCID1_Y |
NFCID1 byte Y |
||||||||||||||||||||||||||||||||
C | RW |
NFCID1_X |
NFCID1 byte X |
||||||||||||||||||||||||||||||||
D | RW |
NFCID1_W |
NFCID1 byte W |
Address offset: 0x594
Second last NFCID1 part (7 or 10 bytes ID)
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
C |
C |
C |
C |
C |
C |
C |
C |
B |
B |
B |
B |
B |
B |
B |
B |
A |
A |
A |
A |
A |
A |
A |
A |
|||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
NFCID1_V |
NFCID1 byte V |
||||||||||||||||||||||||||||||||
B | RW |
NFCID1_U |
NFCID1 byte U |
||||||||||||||||||||||||||||||||
C | RW |
NFCID1_T |
NFCID1 byte T |
Address offset: 0x598
Third last NFCID1 part (10 bytes ID)
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
C |
C |
C |
C |
C |
C |
C |
C |
B |
B |
B |
B |
B |
B |
B |
B |
A |
A |
A |
A |
A |
A |
A |
A |
|||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
NFCID1_S |
NFCID1 byte S |
||||||||||||||||||||||||||||||||
B | RW |
NFCID1_R |
NFCID1 byte R |
||||||||||||||||||||||||||||||||
C | RW |
NFCID1_Q |
NFCID1 byte Q |
Address offset: 0x59C
Controls the auto collision resolution function. This setting must be done before the NFCT peripheral is activated.
When modifiying this register bit 1 must be written to '1'.
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
A |
||||||||||||||||||||||||||||||||||
Reset 0x00000002 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
MODE |
Enables/disables auto collision resolution |
||||||||||||||||||||||||||||||||
Enabled |
0 |
Auto collision resolution enabled |
|||||||||||||||||||||||||||||||||
Disabled |
1 |
Auto collision resolution disabled |
Address offset: 0x5A0
NFC-A SENS_RES auto-response settings
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
E |
E |
E |
E |
D |
D |
D |
D |
C |
C |
B |
A |
A |
A |
A |
A |
|||||||||||||||||||
Reset 0x00000001 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
BITFRAMESDD |
Bit frame SDD as defined by the b5:b1 of byte 1 in SENS_RES response in the NFC Forum, NFC Digital Protocol Technical Specification |
||||||||||||||||||||||||||||||||
SDD00000 |
0 |
SDD pattern 00000 |
|||||||||||||||||||||||||||||||||
SDD00001 |
1 |
SDD pattern 00001 |
|||||||||||||||||||||||||||||||||
SDD00010 |
2 |
SDD pattern 00010 |
|||||||||||||||||||||||||||||||||
SDD00100 |
4 |
SDD pattern 00100 |
|||||||||||||||||||||||||||||||||
SDD01000 |
8 |
SDD pattern 01000 |
|||||||||||||||||||||||||||||||||
SDD10000 |
16 |
SDD pattern 10000 |
|||||||||||||||||||||||||||||||||
B | RW |
RFU5 |
Reserved for future use. Shall be 0. |
||||||||||||||||||||||||||||||||
C | RW |
NFCIDSIZE |
NFCID1 size. This value is used by the auto collision resolution engine. |
||||||||||||||||||||||||||||||||
NFCID1Single |
0 |
NFCID1 size: single (4 bytes) |
|||||||||||||||||||||||||||||||||
NFCID1Double |
1 |
NFCID1 size: double (7 bytes) |
|||||||||||||||||||||||||||||||||
NFCID1Triple |
2 |
NFCID1 size: triple (10 bytes) |
|||||||||||||||||||||||||||||||||
D | RW |
PLATFCONFIG |
Tag platform configuration as defined by the b4:b1 of byte 2 in SENS_RES response in the NFC Forum, NFC Digital Protocol Technical Specification |
||||||||||||||||||||||||||||||||
E | RW |
RFU74 |
Reserved for future use. Shall be 0. |
Address offset: 0x5A4
NFC-A SEL_RES auto-response settings
Bit number | 31 | 30 | 29 | 28 | 27 | 26 | 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | |||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ID |
E |
D |
D |
C |
C |
B |
A |
A |
|||||||||||||||||||||||||||
Reset 0x00000000 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | |||
ID | Access | Field | Value ID | Value | Description | ||||||||||||||||||||||||||||||
A | RW |
RFU10 |
Reserved for future use. Shall be 0. |
||||||||||||||||||||||||||||||||
B | RW |
CASCADE |
Cascade as defined by the b3 of SEL_RES response in the NFC Forum, NFC Digital Protocol Technical Specification (controlled by hardware, shall be 0) |
||||||||||||||||||||||||||||||||
C | RW |
RFU43 |
Reserved for future use. Shall be 0. |
||||||||||||||||||||||||||||||||
D | RW |
PROTOCOL |
Protocol as defined by the b7:b6 of SEL_RES response in the NFC Forum, NFC Digital Protocol Technical Specification |
||||||||||||||||||||||||||||||||
E | RW |
RFU7 |
Reserved for future use. Shall be 0. |
Symbol | Description | Min. | Typ. | Max. | Units | ||||
---|---|---|---|---|---|---|---|---|---|
fc |
Frequency of operation |
13.56 | MHz | ||||||
CMI |
Carrier modulation index |
95 | % | ||||||
DR |
Data Rate |
106 | kbps | ||||||
Vsense |
Peak differential Field detect threshold level on NFC1-NFC21 |
1.2 | Vp | ||||||
Imax |
Maximum input current on NFCT pins |
80 | mA |
Symbol | Description | Min. | Typ. | Max. | Units | ||||
---|---|---|---|---|---|---|---|---|---|
tactivate |
Time from task_ACTIVATE in SENSE or DISABLE state to ACTIVATE_A or IDLE state2 |
500 | µs | ||||||
tsense |
Time from remote field is present in SENSE mode to FIELDDETECTED event is asserted |
20 | µs |