Fixed anomalies

The anomalies listed in this table are no longer present in the current chip version.

For a detailed description of the fixed anomalies, see the Errata for revision Engineering A.

Table 1. Fixed anomalies
ID Domain Module Description
1 Application REGULATORS VREGH short circuit protection is not functional
2 Application TAD Accessing external QSPI memory without configuring QSPI makes application core unresponsive
3 Application SAADC VDDHDIV5 is not functional
4 Application CLOCK Changing application core frequency register HFCLKCTRL requires additional register initialization
5 Application TAD Trace is not functional when application core is running at 128 MHz
7 Application USBD USBD is not functional
8 Application WDT WDT1 is not functional
9 Application TAD TPIU is missing from ROM table
10 Network CCM Reading CNFPTR, INPTR, OUTPTR, and SCRATCHPTR pointers returns incorrect address
11 Network ACL Reading ACL[n].ADDR returns incorrect address
12 Application QSPI SCKFREQ is not functional at 96 MHz
13 Application, Network GPIO Bits in LATCH register are incorrectly set to 1
14 Network TIMER CC[6] and CC[7] are not functional
15 Application, Network UARTE Odd parity setting is not functional
16 Network RADIO POWER register is not functional
18 Application I2S 32-bit sample widths and 8-bit sample in a 16-bit half-frame are not functional
19 Application SPU Flash memory space is divided into 32 regions of 32 KiB
20 Application, Network RTC TASKS_CAPTURE[n], SUBSCRIBE_CAPTURE[n], and SHORTS registers are not functional
21 Application, Network TWIM 1000 kbps baud rate is not functional
22 Application SPU CPULOCK register is not functional
23 Application SAADC Events are not generated when switching from scan mode to no-scan mode with BURST enabled
26 Application, Network CTRL-AP APPROTECT.DISABLE and SECUREAPPROTECT.DISABLE registers are not functional
27 Application, Network CTRL-AP STATUS register is not functional
28 Application, Network TIMER INTEN register is not functional
29 Network SWI SWIRQ is not functional
30 Network RESET LCTRLAP field in RESETREAS register is not functional
31   TAD Multidrop serial wire debug is not functional
32 Network GPIO GPIO pins assigned to network core do not retain their state in System OFF mode
33 Application CLOCK LFRC frequency starts drifting even if calibration task is triggered
34 Network CTRL-AP Erase all is not functional with APPROTECT enabled
36 Application I2S Excessive power consumption after using I2S STOP task
42 Application CLOCK Reset value of HFCLKCTRL is invalid
45 Application SPIM Receive is not functional at 32 Mbps
46 Application CLOCK LFRC has higher current consumption
49 Application, Network POWER SLEEPENTER and SLEEPEXIT events are asserted after pin reset
50 Application SPU Arm TrustZone region numbers for FICR, UICR, CACHEINFO, and CACHEDATA are incorrect
51 Application SPU Accessing FICR, UICR, CACHEINFO, or CACHEDATA from non-secure state gives bus error
52 Application, Network VMC RAM block is not writable immediately on power-up
53 Application REGULATORS Current consumption in normal voltage mode is higher in System ON idle
54 Network REGULATORS Current consumption in normal voltage mode is higher in System ON idle and System OFF
57 Application I2S EVENTS_FRAMESTART and PUBLISH_FRAMESTART registers are not functional
58 Application I2S BYPASS in CONFIG.CLKCONFIG is not functional
59 Application QDEC QDEC0 is not functional
62 Application, Network UICR HFXOCNT register is not functional
64 Application REGULATORS VREGMAIN has invalid configuration when CPU is running
66 Application GPIO P1.PIN_CNF[2-3], P0.PIN_CNF[8-18] DRIVE cannot be set in some configurations
67   DEVICE ESD HBM is less than 2 kV
69 Application REGULATORS VREGMAIN configuration is not retained in System OFF
72 Application REGULATORS Current consumption in high voltage mode is higher in System ON idle and System OFF
73 Application, Network TIMER ONESHOTEN[n] registers are located at an incorrect address offset
74 Application, Network TIMER COMPARE[i]_STOP is located at an incorrect bit number in the SHORTS register
77   TAD Debug power-up request is not acknowledged
79 Application QDEC QDEC1 is not functional
80 Application PWM PWM3 is not functional
81 Application SPIM SPIM2 and SPIM3 are not functional
82 Application TWIM TWIM2 and TWIM3 are not functional
83 Application SPIS SPIS2 and SPIS3 are not functional
84 Application UARTE UARTE2 and UARTE3 are not functional
85 Application NVMC Reading or executing from flash memory can lead to errors when scaling frequency
86 Application, Network CLOCK EVENTS_DONE is not functional
90 Application GPIO PIN_CNF[n] MCUSEL is reset by application core soft reset
91 Network RADIO Ramp-up is slower than specified
93 Network NVMC Writing to flash requires high voltage on VREGRADIO
95 Network REGULATORS VREGRADIO DC/DC can malfunction
97 Application, Network UICR ERASEPROTECT or APPROTECT is occasionally enabled or device startup may fail
105 Application SPIM, SPIS, TWIM, TWIS, UARTE Peripheral has higher than expected current consumption
106 Application SPIM SPIM4 is not functional with GPIO.PIN_CNF[n].MCUSEL configured as Peripheral
109 Application GPIOTE LATENCY register is not functional
110 Application QSPI QSPI is not functional with GPIO.PIN_CNF[n].MCUSEL configured as Peripheral
114 Network CPU Accessing application core flash causes processor to become unresponsive
115 Application CRYPTOCELL, USBD Peripheral cannot do DMA transfers from flash when application core processor is sleeping
116 Network RADIO Device spurious emission during transmit is higher than expected
Parent topic: nRF5340 Engineering D Errata