Change log

See the following list for an overview of changes from previous versions of this document.

Table 1. Change log
Version Date Change
nRF52832 Engineering B v1.3 28.09.2016
  • Added: No. 108. “RAM content cannot be trusted upon waking up from System ON Idle or System OFF mode”
nRF52832 Engineering B v1.2 05.07.2016
  • Added: No. 84. “ISOURCE not functional”
  • Added: No. 86. “Triggering START task after offset calibration may write a sample to RAM”
  • Added: No. 87. “Unexpected wake from System ON Idle when using FPU”
  • Added: No. 88. “Increased current consumption when configured to pause in System ON idle”
  • Added: No. 89. “Static 400 µA current while using GPIOTE”
  • Added: No. 97. “High current consumption in System ON Idle mode”
nRF52832 Engineering B v1.1 17.02.2016
  • Deleted: No. 53. “Using SCB.AIRCR.VECTRESET may get the chip into an undefined state” (not relevant)
  • Updated: No. 70. “Not able to wake CPU from System ON IDLE”
  • Updated: No. 73. “Event lost”
  • Updated: No. 78. “High current consumption when using timer STOP task only”
  • Added: No. 79. “ A false EVENTS_FIELDDETECTED event occurs after the field is lost”
  • Added: No. 81. “PIN_CNF is not retained when in debug interface mode”
  • Added: No. 83. “STOPPED event occurs twice if the STOP task is triggered during a transaction”
nRF52832 Engineering B v1.0 21.01.2016
  • Created separate document for IC revision Engineering B.
nRF52832-PAN v1.2 11.12.2015
  • Added: No. 67. “Some events cannot be used with the PPI”
  • Added: No. 68. “EVENTS_HFCLKSTARTED can be generated before HFCLK is stable”
  • Added: No. 70. “Not able to wake CPU from System ON IDLE”
  • Added: No. 71. “RCOSC calibration”
  • Added: No. 72. “TASKS_ACTIVATE cannot be used with the PPI”
  • Added: No. 73. “Event lost”
  • Added: No. 74. “Started events fires prematurely”
  • Added: No. 75. “Increased current consumption”
  • Added: No. 76. “READY event is set sooner than it should”
  • Added: No. 77. “RC oscillator is not calibrated when first started”
  • Added: No. 78. “High current consumption when using timer STOP task only”
nRF52832-PAN v1.1 09.10.2015
  • Added: No. 12. “Reference ladder is not correctly calibrated”
  • Added: No. 15. “RAM[x].POWERSET/CLR read as zero”
  • Added: No. 20. “Register values are invalid”
  • Added: No. 30. “STOP Task and STOPPED Event are not functional”
  • Added: No. 36. “Some registers are not reset when expected”
  • Added: No. 31. “Calibration values are not correctly loaded from FICR at reset”
  • Added: No. 51. “Aligned stereo slave mode does not work”
  • Added: No. 53. “Using SCB.AIRCR.VECTRESET may get the chip into an undefined state”
  • Added: No. 54. “Wrong LRCK polarity in Aligned mode”
  • Added: No. 55. “RXPTRUPD and TXPTRUPD events asserted after STOP”
  • Added: No. 58. “SPIM clocks out an additional byte when RXD.MAXCNT = 1”
  • Added: No. 62. “Can draw current when not enabled”
  • Added: No. 63. “DC/DC does not automatically switch off in System ON IDLE”
  • Added: No. 64. “Only full bytes can be received or transmitted”

Documentation feedback | Developer Zone | Subscribe | Updated 2016-09-28